Difference between revisions of "HMC5883L"

From Wiki
Jump to: navigation, search
(Resource)
(Features)
 
(5 intermediate revisions by the same user not shown)
Line 6: Line 6:
  
 
=='''Features'''==
 
=='''Features'''==
(1)The Honeywell HMC5883L is a surface-mount, multi-chip module designed for low-field magnetic sensing with a digital interface for applications such as low cost compassing and magnetometry
+
(1)The Honeywell HMC5883L is a surface-mount, multi-chip module designed for low-field magnetic sensing with a digital interface for applications such as low cost compassing and magnetometry
  
(2)The 12-Bit ADC coupled with low noise AMR sensors achieves 5 milli-gauss field resolution in ±8 gauss fields
+
(2)The 12-Bit ADC coupled with low noise AMR sensors achieves 5 milli-gauss field resolution in ±8 gauss fields
  
(3)Low voltage operations and low power consumption; supports built-in self-test  
+
(3)Low voltage operations and low power consumption; supports built-in self-test  
  
(4)Built-in strap drive circuits, I2C digital interface, wide magnetic field range (+/-8 oe)
+
(4)Built-in strap drive circuits, I2C digital interface, wide magnetic field range (+/-8 oe)
 
+
(5)Working voltage: 3.3v-5v; PCB size: 1.3 x 2.3 cm (HMC5883L size: 3.0 x 3.0 x 0.9 mm), with a16-pin leadless chip carrier (LCC)
+
  
 +
(5)Working voltage: 3.3v-5v; PCB size: 1.3 x 2.3 cm (HMC5883L size: 3.0 x 3.0 x 0.9 mm), with a16-pin leadless chip carrier (LCC)
  
 
=='''Schematic'''==
 
=='''Schematic'''==
  
 
[[File:HMC2.jpg]]
 
[[File:HMC2.jpg]]
'''
+
 
==Pin Function'''==
+
=='''Pin Function'''==
 
*'''VCC+5V''' - power pin, give it 3.3v-5VDC. For Arduino,recommand 5v
 
*'''VCC+5V''' - power pin, give it 3.3v-5VDC. For Arduino,recommand 5v
  
Line 73: Line 72:
  
 
=='''Resource'''==
 
=='''Resource'''==
[https://www.sunfounder.com/wiki/index.php?title=File:Adafruit_HMC5883_Unified.zip Adafruit_HMC5883_Unified][[File:ZIP.jpg]]<br>
+
[http://wiki.sunfounder.cc/images/0/06/Adafruit_HMC5883_Unified.zip Adafruit_HMC5883_Unified][[File:ZIP.jpg]]<br>
[https://www.sunfounder.com/wiki/index.php?title=File:Adafruit_Sensor.zip Adafruit_Sensor][[File:ZIP.jpg]]<br>
+
[http://wiki.sunfounder.cc/images/5/51/Adafruit_Sensor.zip Adafruit_Sensor][[File:ZIP.jpg]]<br>
[https://www.sunfounder.com/wiki/index.php?title=File:HMC5883L_datasheet.pdfHMC5883L_datasheett][[File:PDF.jpg]]<br>
+
[http://wiki.sunfounder.cc/images/0/0a/HMC5883L_datasheet.pdf pdfHMC5883L_datasheett][[File:PDF.jpg]]<br>

Latest revision as of 07:17, 20 March 2017

Introduction

Hmc1.jpg

The module includes a state-of-the-art, high-resolution HMC118X series magneto-resistive sensor, plus an ASIC containing amplification, automatic degaussing strap drivers, offset cancellation, and a 12-bit ADC that enables 1° to 2° compass heading accuracy. The I2C serial bus allows for easy interface.

Features

(1)The Honeywell HMC5883L is a surface-mount, multi-chip module designed for low-field magnetic sensing with a digital interface for applications such as low cost compassing and magnetometry

(2)The 12-Bit ADC coupled with low noise AMR sensors achieves 5 milli-gauss field resolution in ±8 gauss fields

(3)Low voltage operations and low power consumption; supports built-in self-test

(4)Built-in strap drive circuits, I2C digital interface, wide magnetic field range (+/-8 oe)

(5)Working voltage: 3.3v-5v; PCB size: 1.3 x 2.3 cm (HMC5883L size: 3.0 x 3.0 x 0.9 mm), with a16-pin leadless chip carrier (LCC)

Schematic

HMC2.jpg

Pin Function

  • VCC+5V - power pin, give it 3.3v-5VDC. For Arduino,recommand 5v
  • GND - ground pin
  • SDA and SCL - these are the I2C data and clock pins used to send and receive data from the module to your microcontroller. There are 10K pullups on these pins to the 3.3v pin. You can connect these pins to 5V I2C lines, there are level shifters on board to safely bring the pins down to 3V
  • DRDY - this it the 'data ready' pin output. If you want to stream data at high speed (higher than 100 times a second) you may want to listen to this pin for when data is ready to be read. Check the datasheet for more details about using the DRDY pin, we don't use it because we don't read that fast!

Test Experiment

1.Build the circuit

HMC5883L--------------- Uno/Mega2560
VCC------------------- 5V
GND------------------- GND
SCL------------------- A5/ pin21 mega2560
SDA------------------- A4/pin20 mega2560
DRDY------------------ N/C

Hmc3.jpg

2.Upload the code

1)Before you Upload the code ,you need to add the two library to the Arduino\libraries, Open IDE,click to Sketech -> Include library -> Add .ZIP Library

Hmc4.jpg

2)Find the Adafruit_HMC5883L_Unified.zip library, click to Open. Import the Adafruit_Sensor.zip library from the libraries folder in the same way.

Hmc5.jpg

3)Click to File -> Examples -> Adafruit_HMC5883L_Unified ->magsensor

Hmc6.jpg

4)Select correct Board

Hmc7.jpg

And then correct Port

Hmc8.jpg

5)click the Upload icon to upload the code to the control board

Hmc9.jpg

6)Open the serial monitor, You will see some quick spec's about the HMC5883L and then a stream of data with X Y Z magnetometer data in uTeslas and then a calculated heading. If you hold the module so that it is parallel with the ground then it will point you in the direction of North! 

Hmc10.jpg

Resource

Adafruit_HMC5883_UnifiedZIP.jpg
Adafruit_SensorZIP.jpg
pdfHMC5883L_datasheettPDF.jpg