Difference between revisions of "Flame Sensor Module"

From Wiki
Jump to: navigation, search
(Introduction of Pins)
(Introduction of Pins)
 
(11 intermediate revisions by the same user not shown)
Line 1: Line 1:
 
=='''Introduction'''==
 
=='''Introduction'''==
[[File:Flame Sensor Module.jpg]] <br>
+
[[File:PWR4.jpg]] <br>
 
Infrared Flame Sensor is used to detect the ignition sources and the intensity of light for robots. Yet, this product is more sensitive to ignition sources.
 
Infrared Flame Sensor is used to detect the ignition sources and the intensity of light for robots. Yet, this product is more sensitive to ignition sources.
 +
 
=='''Features'''==
 
=='''Features'''==
 
<ol>
 
<ol>
Line 32: Line 33:
 
| Analog signal output
 
| Analog signal output
 
|}
 
|}
 +
 
=='''Principle'''==
 
=='''Principle'''==
Flame Sensor applies the principle that the infrared ray is sensitive to flame. It uses the tailor-made photo diode to detect flame and converts the brightness of flame to the variable</br>
+
Flame Sensor applies the principle that the infrared ray is sensitive to flame. It uses the tailor-made photo diode to detect flame and converts the brightness of flame to the variable<br>
level signal, then inputs them into CPU. CPU executes relevant program according to the changing level signal.
+
level signal, then inputs them into CPU. CPU executes relevant program according to the changing level signal.<br>
 +
[[File:Flame Sensor Module(Principle).jpg]] <br>
 +
=='''Experimental Procedures For Arduino '''==
 +
[[File:Flame Sensor Module(Fritzing).jpeg]]<br>
 +
'''Step 1:''' Connect the circuit:<br>
 +
'''Step 2:''' Compile and upload the code.<br><br>
 +
In order to keep the D0 output of the flame sensor working well, you should adjust the knob of the potentiometer to let the D0 output low level when it detects flame. The operations are as follows. Expose the module to flame or strong light and turn the knob of the potentiometer gently till the D0 indicator light is on. Now the testing is done, and you need to start flashing your codes. <br><br>
 +
 
 +
The detection angle of far infrared sensor is 60°, you need to keep the detected objects being in the detection range at the time of testing.<br>
 +
<pre>
 +
/****************************************/
 +
const int a0Pin = A0;
 +
const int d0Pin = 2;
 +
const int ledPin = 13;
 +
int lightIntensityVal = 0;
 +
 
 +
void setup()
 +
{
 +
  Serial.begin(9600);
 +
  pinMode(a0Pin, INPUT);
 +
  pinMode(d0Pin, INPUT);
 +
  pinMode(ledPin, OUTPUT);
 +
}
 +
 
 +
void loop()
 +
{
 +
  Serial.print("D0: ");
 +
  Serial.print(digitalRead(d0Pin));
 +
  Serial.print(" \t");
 +
  Serial.print("A0: ");
 +
  Serial.println(analogRead(a0Pin));
 +
  lightIntensityVal = digitalRead(d0Pin);
 +
  if (lightIntensityVal == 0) {
 +
    digitalWrite(ledPin, HIGH);
 +
  } else {
 +
    digitalWrite(ledPin, LOW);
 +
  }
 +
}
 +
 
 +
</pre>
 +
[[File:Flame Sensor Module(serial).jpeg]]<br>
 +
When flame or strong light is detected, the analog value will decrease and the module will output low level. Meanwhile, the indicator light D0-LED will light up.<br>
 +
Notice: The working temperature of the far infrared flame sensor is -25°~85°, and the storage temperature is 30°~100°. So the detector of the sensor can easily get broken down when  working under the temperature above the range. So please do not let your detector be too close to the heat source.

Latest revision as of 02:55, 26 September 2019

Introduction

PWR4.jpg
Infrared Flame Sensor is used to detect the ignition sources and the intensity of light for robots. Yet, this product is more sensitive to ignition sources.

Features

  1. The module can detect flame or light source whose wavelength ranges from 760nm to 1100nm. The detection distance of the flame of lighter is 80 cm. The larger the flame intensity, the farther the test distance is.
  2. Detection Angle: about 60 degrees.
  3. The module is sensitive to the flame spectrum.
  4. Adjustable sensitivity (adjust by using the blue potentiometer).
  5. Comparator output, clean signal, regular waveform, strong driving ability, current more than 15mA.
  6. Working Voltage: 3.3V~5V.
  7. Output Form: DO digital switch output (0 and 1) and AO analog voltage output.
  8. Holes for easy mounting.
  9. Small Panel Size of PCB: 3.2cm x 1.4cm.
  10. Applying the wide voltage LM393 comparator.

Introduction of Pins

Pin Introduction
VCC The anode of power supply(3.3v-5v)
GND The cathode of power supply
D0 TTl switch signal output
A0 Analog signal output

Principle

Flame Sensor applies the principle that the infrared ray is sensitive to flame. It uses the tailor-made photo diode to detect flame and converts the brightness of flame to the variable
level signal, then inputs them into CPU. CPU executes relevant program according to the changing level signal.
Flame Sensor Module(Principle).jpg

Experimental Procedures For Arduino

Flame Sensor Module(Fritzing).jpeg
Step 1: Connect the circuit:
Step 2: Compile and upload the code.

In order to keep the D0 output of the flame sensor working well, you should adjust the knob of the potentiometer to let the D0 output low level when it detects flame. The operations are as follows. Expose the module to flame or strong light and turn the knob of the potentiometer gently till the D0 indicator light is on. Now the testing is done, and you need to start flashing your codes.

The detection angle of far infrared sensor is 60°, you need to keep the detected objects being in the detection range at the time of testing.

/****************************************/
const int a0Pin = A0;
const int d0Pin = 2;
const int ledPin = 13;
int lightIntensityVal = 0;

void setup()
{
  Serial.begin(9600);
  pinMode(a0Pin, INPUT);
  pinMode(d0Pin, INPUT);
  pinMode(ledPin, OUTPUT);
}

void loop()
{
  Serial.print("D0: ");
  Serial.print(digitalRead(d0Pin));
  Serial.print(" \t");
  Serial.print("A0: ");
  Serial.println(analogRead(a0Pin));
  lightIntensityVal = digitalRead(d0Pin);
  if (lightIntensityVal == 0) {
    digitalWrite(ledPin, HIGH);
  } else {
    digitalWrite(ledPin, LOW);
  }
}

Flame Sensor Module(serial).jpeg
When flame or strong light is detected, the analog value will decrease and the module will output low level. Meanwhile, the indicator light D0-LED will light up.
Notice: The working temperature of the far infrared flame sensor is -25°~85°, and the storage temperature is 30°~100°. So the detector of the sensor can easily get broken down when working under the temperature above the range. So please do not let your detector be too close to the heat source.