7 Inch Screen Manual

7 Inch DIY Touch Screen

Supporting the Seven-inch Screen

Use a nut (M3) and a copper post (M3 * 8 + 6) to support the seven-inch touch screen.

Rendering

This 7-inch touch screen is compatible with any version of the Raspberry Pi.

With a Raspberry Pi 4

Connect the Raspberry Pi 4 to HDMI with a micro HDMI cable.

Wire the USB cable up to Raspberry Pi 4.

Give it a power supply, Plug and play.

Adjust the Resolution of Raspberry Pi 4

Step 1: Unfold the menu bar of Raspberry Pi.

Step 2: Select screen configuration.

Step 3: Select screen configuration.

Step 4: Select Screens.

Step 5: Choose the resolution you want.

With a Raspberry Pi 3

Plug a dual-head HDMI cable in Raspberry Pi 3.

Connect the Raspberry Pi 3 with a USB cable.

Attach a power supply to it, turn it on.

Adjust the Resolution of Raspberry Pi 3

Step 1: Open config.txt
There are two methods to do so.
Method A: First prepare a computer on Windows, Mac or Linux, and a TF card on which the Raspbian system has been burnt. Plug the TF card into the computer with a card reader. Now, open /boot and find the config.txt file. If your computer runs on Windows, DO NOT open the file by Word (also better not notepad) in case of format issues. You are advised to use other edit tools like Notepad++ .
Method B: Log in to Raspberry Pi remotely. Run the command to edit config.txt.

sudo nano /boot/config.txt

Step 2: Modify the /boot/config.txt file
In either way, now the file config.txt is opened.
1) Define a custom CVT mode (since Raspberry Pi uses the standard rate when 1024x600 is not included, you need to set the aspect ratio as 16:9, i.e. 1024x576) add the following lines below #hdmi_force_hotplug=1.

hdmi_cvt=1024 576 60 3 0 0 0

hdmi_cvt=<width> <height> <framerate> <aspect> <margins>
<interlace>

Value	Default	Description
width	(required)	width in pixels
height	(required)	height in pixels
height in pixels	(required)	framerate in Hz
aspect	3	aspect ratio 1=4:3, 2=14:9, 3=16:9, 4=5:4,5=16:10, 6=15:9
margins	0	0=margins disabled, 1=margins enabled
interlace	0	0=progressive, 1=interlaced
rb	0	0=normal, 1=reduced blanking

2) Find the following lines (If there is a "#" mark at the beginning of any of the three lines, which means they are comments, delete the mark. The asterisk "*" represents the value.

hdmi_group=*
hdmi_mode=*
hdmi_drive=*

3) Modify the value, like this:

hdmi_group=2
hdmi_mode=87
....
hdmi_drive=2

hdmi_group=2 means DMT (Display Monitor Timings; the standard typically used by monitors)
hdmi_mode=87 indicates the resolution bit.
hdmi_drive=2 selects the Normal HDMI mode.
For more details about configuring config.txt, refer to Raspberry Pi official
website: https://www.raspberrypi.org/documentation/configuration/config-txt.md.
After the modification is done, save and exit.
Step 3: Connect Raspberry Pi
If you change the commands on your PC, after mounting the TF card safely, plug it into the Raspberry Pi. Then connect the power of the Raspberry Pi and the display.
If you log in the Raspberry Pi remotely with ssh, type in the command sudo reboot.

SPECIFICATION

1、 GENERAL INFORMATION

2、 ABSOLUTE MAXIMUM RATINGS

Parameter of absolute maximum ratings	Symbol	Min	Max	Unit
Operating temperature	Top	－10	60	60
Storage temperature	Tst	－20	70	℃
Humidity	RH	`	90%(Max 60℃)	RH

Note: Absolute maximum ratings means the product can withstand short-term, not more than 120 hours. If the product is a long time to withstand these conditions, the life time would be shorter.

Parameter of DC characteristics	Symbol	Min.	Min.	Max.	Unit
PCB operating voltage	VUSB	`	5.0	`	V
LCD I/O operating voltage	VDD	3.0	3.3	3.6	V
Input voltage ‘H’ level	VIH	0.7*VDD	`	VDD	V
Input voltage ‘L’ level	VIL	VSS	`	0.3*VDD	V
Output voltage ‘H’ level	VOH	VDD-0.4	`	VDD	V
Output voltage ‘L’ level	VOL	VSS	`	VSS+0.4	V

3、 CTP CHARACTERISTICS

Item of CTP characteristics	Specification	Unit	Remark
Panel Type	Glass Cover + Glass Sensor	`	`
Resolution	1024 × 600	pixel	`
Surface Hardness	≥6H	`	`
Transparency	＞82%	`	`
Driver IC	`	`	`
Interface Type	USB	`	`
Support Points	5	`	`
Sampling Rate	20~100	Hz	`
Supply voltage	3.3	V	`

4、 INTERFACE DESCRIPTION

Symbol	DESCRIPTION
VUSB	USB Power
D-	USB Data
D+	USB Data+
NC	No connection
GND	Power Ground