Difference between revisions of "Esp8266 Wifi Module"
(→Resource) |
(→Resource) |
||
| Line 115: | Line 115: | ||
[http://www.sunfounder.com/wiki/index.php/File:ESP8266_Datasheet_v4.4.pdf ESP8266_Datasheet][[File:PDF.jpg]]<br> | [http://www.sunfounder.com/wiki/index.php/File:ESP8266_Datasheet_v4.4.pdf ESP8266_Datasheet][[File:PDF.jpg]]<br> | ||
http://www.devicebit.com/home/login?rurl=http://www.devicebit.com/user/clientindex | http://www.devicebit.com/home/login?rurl=http://www.devicebit.com/user/clientindex | ||
| + | http://www.sunfounder.com/wiki/index.php?title=File:Relay_datasheet.pdf | ||
Revision as of 10:08, 5 April 2016
Contents
Introduction
ESP8266 is an UART-WiFi transparent transmission module with ultralow power consumption, specially designed for the needs of a new connected world. It offers a complete and self-contained Wi-Fi networking solution, allowing it to either host the application or to offload all Wi-Fi networking functions from another application processor.
ESP8266 has powerful on-board processing and storage capabilities that allow it to be integrated with the sensors and other application specific devices through its GPIOs with minimal development up-front and minimal loading during runtime. Its high degree of on-chip integration allows for minimal external circuitry, and the entire solution, including front-end module, is designed to occupy minimal PCB area. ESP8266 Serial Wifi Wireless Transceiver Module is suitable for Uno, Mega 2560 and Nano.
[1]
Pin Functions
| Pin | Name | Description |
|---|---|---|
| 1 | TXD | 1）UART_TXD，sending； 2）General Purpose Input/Output：GPIO1； |
| 2 | GND | GND |
| 3 | CU_PD | 1）Working at high level; 2）Power off when low level is supplied |
| 4 | GPIO2 | 1）It should be high level when power on, hardware pull-down is not allowed; 2）Pull-up by default; |
| 5 | GPIO16 | External Reset signal, reset when low level is supplied; work when high level is supplied (high level by default); |
| 6 | GPIO0 | 1）WiFi Status indicator; 2）Operation mode selection: |
| 7 | VCC | Power Supply(3.3V) |
| 8 | RXD | 1）UART_RXD，Receiving 2）General Purpose Input/Output: GPIO3; |
Schematic
Features
• 802.11 b/g/n
• Integrated low power 32-bit MCU
• Integrated 10-bit ADC
• Integrated TCP/IP protocol stack
• Integrated TR switch, balun, LNA, power amplifier and matching network
• Integrated PLL, regulators, and power management units
• Supports antenna diversity
• Wi-Fi 2.4 GHz, support WPA/WPA2
• Support STA/AP/STA+AP operation modes
• Support Smart Link Function for both Android and iOS devices
• SDIO 2.0, (H) SPI, UART, I2C, I2S, IR Remote Control, PWM, GPIO
• A-MPDU & A-MSDU aggregation & 0.4s guard interval
• Deep sleep power <10uA, Power down leakage current < 5uA
• Wake up and transmit packets in < 2ms
• Standby power consumption of < 1.0mW (DTIM3)
• +20 dBm output power in 802.11b mode
• Operating temperature range -40C ~ 125C
• FCC, CE, TELEC, Wi-Fi Alliance, and SRRC certified
How to Test and Debug Esp8266
Preparation
-1 * PL2303HXD
-1 * SunFounder Uno Board
-1 * ESP8266
Procedures
Step 1: wire
Connect UTXD of ESP8266 to RXD of PL2303, URXD to TXD, CH_PD to 5v, GND to GND, and VCC to 3.3v. The Uno board here is used to supply 3.3v power. PL2303 is a USB to Serial Bridge Controller. You can also use other components, such as FTDI.
Step 2：set parameters
After wiring, open the serial port debug tool sscom32. Set parameters at first.
1) Open the serial port, click Open Com. Select the correct port, as shown below.
2) Select the correct baud rate. Here select 115200 bps. Click SendNew, as shown below.
Step3:AT instructions
Now, you can start to send instructions. Enter "AT+RST" in the text box. It’s used to restart the module. If ESP8266 goes well, OK will be sent, as shown below:
You can also send other instructions, such as "AT+GMR". It is used to check the version of AT commands and SDK that you are using, the type of which is "executed".
For more information about ESP8266 AT Instructions. please refer to 4A-ESP8266__AT Instrction Set__EN_v0.23.pdf.
Resource
ESP8266_AT_Instrction_Set
ESP8266_Module_User_Guide
ESP8266_Datasheet
http://www.devicebit.com/home/login?rurl=http://www.devicebit.com/user/clientindex
http://www.sunfounder.com/wiki/index.php?title=File:Relay_datasheet.pdf
