Difference between revisions of "PCF8591 8-bit A/D and D/A converter Module"

From Wiki
Jump to: navigation, search
Line 3: Line 3:
 
The PCF8591 module consists of a master control chip PCF8591, some resistors and capacitors .It can data acquisition device and has four analog inputs, one analog output and a serial I2C-bus interface. Three address pins A0, A1 and A2 are used for programming the hardware address, allowing the use of up to eight devices connected to the I2C-bus without additional hardware. Address, control and data to and from the device are transferred serially via the two-line bidirectional I2C-bus.  
 
The PCF8591 module consists of a master control chip PCF8591, some resistors and capacitors .It can data acquisition device and has four analog inputs, one analog output and a serial I2C-bus interface. Three address pins A0, A1 and A2 are used for programming the hardware address, allowing the use of up to eight devices connected to the I2C-bus without additional hardware. Address, control and data to and from the device are transferred serially via the two-line bidirectional I2C-bus.  
 
The schematic diagram of the module is as follows:
 
The schematic diagram of the module is as follows:
[[File:Cfdf.png]]
+
[[File:Cfdf.png]]<br>
 
<font color="red">
 
<font color="red">
 
Note:<br>
 
Note:<br>
Line 27: Line 27:
 
*Address by 3 hardware address pins
 
*Address by 3 hardware address pins
 
=='''Resource'''==
 
=='''Resource'''==
[http://www.lengeek.com/wiki/index.php?title=File:PCF8591.PDF PCF8591 datasheet][[File:PDF.JPG]]
+
[http://www.lengeek.com/wiki/index.php?title=File:PCF8591.PDF PCF8591 datasheet][[File:PDF.jpg]]

Revision as of 06:49, 24 March 2016

Introduction

MG 0964.JPG
The PCF8591 module consists of a master control chip PCF8591, some resistors and capacitors .It can data acquisition device and has four analog inputs, one analog output and a serial I2C-bus interface. Three address pins A0, A1 and A2 are used for programming the hardware address, allowing the use of up to eight devices connected to the I2C-bus without additional hardware. Address, control and data to and from the device are transferred serially via the two-line bidirectional I2C-bus. The schematic diagram of the module is as follows: Cfdf.png
Note:
通过原理图,AIN0上接了一个电位器,如果你用跳线帽接上P3(即电位器旁边的两个引脚),那你就可以用电位器来作为AIN0的输入

By schematics on AIN0 received a potentiometer , if you use the jumper connected to P3 ( ie two pins potentiometer next to it) , then you can potentiometer input as AIN0

PCF8591

The PCF8591 is a single-chip, single-supply low power 8-bit CMOS data acquisition device with four analog inputs, one analog output and a serial I2C-bus interface. Three address pins A0, A1 and A2 are used for programming the hardware address, allowing the use of up to eight devices connected to the I2C-bus without additional hardware. Address, control and data to and from the device are transferred serially via the two-line bidirectional I2C-bus. The functions of the device include analog input multiplexing, on-chip track and hold function, 8-bit analog-to-digital conversion and an 8-bit digital-to-analog conversion. The maximum conversion rate is given by the maximum speed of the I2C-bus.

Block Diagram

20150805143217.png

Pin Function

PCF8591T.png 20150805143308.png

Features

  • Support acquisition of external 4-line voltage inputs (ranging 0-5v), with a single power supply
  • Standard double-sided printed circuit board, 1.16mm thick, with an elegant layout, 3-mm holes at each corner for easy fixing
  • Use an 8-bit successive approximation A/D converter
  • Input/output by an I2C bus
  • Working voltage: 2.5-6V DC; PCB size: 2.4 x 2.8 cm
  • Single supply, low standby current
  • Address by 3 hardware address pins

Resource

PCF8591 datasheetPDF.jpg