Difference between revisions of "Adjust Resolution for Raspberry Pi"
(Created page with "If you are using Raspberry Pi with the screen, you may encounter incomplete display, with black space around. that would be wrong resolution. ==Step 1: Open config.txt== Conne...") |
|||
| (10 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
| − | If you are using Raspberry Pi with the screen, you may encounter incomplete display, with black space around. that would be wrong resolution. | + | If you are using Raspberry Pi with the screen, you may encounter incomplete display, with black space around. that would be wrong resolution.<br> |
| − | + | '''Step 1: Open config.txt'''<br> | |
| − | Connect a mouse and a keyboard to your Raspberry Pi. Click open the Terminal, and type in the command to open config.txt | + | Connect a mouse and a keyboard to your Raspberry Pi. Click open the Terminal, and type in the command to open config.txt<br> |
sudo leafpad /boot/config.txt | sudo leafpad /boot/config.txt | ||
| − | + | '''Step 2: Modify the config.txt file'''<br> | |
| − | Now the file config.txt is opened. | + | Now the file config.txt is opened.<br> |
| − | 1)Define a custom CVT mode add the following lines below #hdmi_force_hotplug=1. hdmi_cvt=1920 1080 60 3 0 0 0 | + | 1)Define a custom CVT mode add the following lines below #hdmi_force_hotplug=1.<br> |
| − | hdmi_cvt=<width> <height> <framerate> <aspect> <margins> <interlace> | + | hdmi_cvt=1920 1080 60 3 0 0 0<br> |
| + | '''hdmi_cvt=<width> <height> <framerate> <aspect> <margins> <interlace>'''<br> | ||
| + | {| class="wikitable" | ||
| + | |Value | ||
| + | |Default | ||
| + | |Default | ||
| + | |- | ||
| + | |width | ||
| + | |(required) | ||
| + | |width in pixels | ||
| + | |- | ||
| + | |height | ||
| + | |(required) | ||
| + | |height in pixels | ||
| + | |- | ||
| + | |framerate | ||
| + | |(required) | ||
| + | |framerate in Hz | ||
| + | |- | ||
| + | |aspect | ||
| + | |3 | ||
| + | |aspect ratio 1=4:3, 2=14:9, 3=16:9, 4=5:4, 5=16:10, 6=15:9 | ||
| + | |- | ||
| + | |margins | ||
| + | |0 | ||
| + | |0=margins disabled, 1=margins enabled | ||
| + | |- | ||
| + | |interlace | ||
| + | |0 | ||
| + | |0=progressive, 1=interlaced | ||
| + | |- | ||
| + | |rb | ||
| + | |0 | ||
| + | |0=normal, 1=reduced blanking | ||
| + | |} | ||
| + | <br> | ||
| + | 2)Find the following lines (If there is a "#" mark at the beginning of any of the three lines, which means they are comments, delete the mark. The asterisk "*" represents the value.<br> | ||
| + | hdmi_group=*<br> hdmi_mode=*<br> hdmi_drive=*<br> | ||
| + | 3)Modify the value, like this:<br> | ||
| + | hdmi_group=2<br> hdmi_mode=87<br> | ||
| + | ....<br> | ||
| + | hdmi_drive=2<br> | ||
| + | '''hdmi_group=2''' means DMT (Display Monitor Timings; the standard typically used by monitors)<br> | ||
| + | '''hdmi_mode=87''' indicates the resolution mode we set before.<br> | ||
| + | '''hdmi_drive=2''' selects the Normal HDMI mode.<br> | ||
| − | + | For more details about configuring config.txt, refer to Raspberry Pi official website: https://www.raspberrypi.org/documentation/configuration/config-txt.md | |
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | After the modification is done, save, exit then reboot your Raspberry Pi and enjoy.<br> | |
| − | + | http://wiki.sunfounder.cc/images/b/b5/Modify_resolution.pdf | |
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | After the modification is done, save, exit then reboot your Raspberry Pi and enjoy. | + | |
Latest revision as of 10:56, 20 February 2019
If you are using Raspberry Pi with the screen, you may encounter incomplete display, with black space around. that would be wrong resolution.
Step 1: Open config.txt
Connect a mouse and a keyboard to your Raspberry Pi. Click open the Terminal, and type in the command to open config.txt
sudo leafpad /boot/config.txt
Step 2: Modify the config.txt file
Now the file config.txt is opened.
1)Define a custom CVT mode add the following lines below #hdmi_force_hotplug=1.
hdmi_cvt=1920 1080 60 3 0 0 0
hdmi_cvt=<width> <height> <framerate> <aspect> <margins> <interlace>
| Value | Default | Default |
| width | (required) | width in pixels |
| height | (required) | height in pixels |
| framerate | (required) | framerate in Hz |
| aspect | 3 | aspect ratio 1=4:3, 2=14:9, 3=16:9, 4=5:4, 5=16:10, 6=15:9 |
| margins | 0 | 0=margins disabled, 1=margins enabled |
| interlace | 0 | 0=progressive, 1=interlaced |
| rb | 0 | 0=normal, 1=reduced blanking |
2)Find the following lines (If there is a "#" mark at the beginning of any of the three lines, which means they are comments, delete the mark. The asterisk "*" represents the value.
hdmi_group=*
hdmi_mode=*
hdmi_drive=*
3)Modify the value, like this:
hdmi_group=2
hdmi_mode=87
....
hdmi_drive=2
hdmi_group=2 means DMT (Display Monitor Timings; the standard typically used by monitors)
hdmi_mode=87 indicates the resolution mode we set before.
hdmi_drive=2 selects the Normal HDMI mode.
For more details about configuring config.txt, refer to Raspberry Pi official website: https://www.raspberrypi.org/documentation/configuration/config-txt.md
After the modification is done, save, exit then reboot your Raspberry Pi and enjoy.
http://wiki.sunfounder.cc/images/b/b5/Modify_resolution.pdf
