Difference between revisions of "Adjust Resolution for Raspberry Pi"
| Line 8: | Line 8: | ||
'''hdmi_cvt=<width> <height> <framerate> <aspect> <margins> <interlace>'''<br> | '''hdmi_cvt=<width> <height> <framerate> <aspect> <margins> <interlace>'''<br> | ||
{| class="wikitable" | {| class="wikitable" | ||
| − | |Value |Default |Default | + | |Value |
| + | |Default | ||
| + | |Default | ||
|- | |- | ||
| − | |width |(required) |width in pixels | + | |width |
| + | |(required) | ||
| + | |width in pixels | ||
|- | |- | ||
| − | |height |(required) |height in pixels | + | |height |
| + | |(required) | ||
| + | |height in pixels | ||
|- | |- | ||
| − | |framerate |(required) |framerate in Hz | + | |framerate |
| + | |(required) | ||
| + | |framerate in Hz | ||
|- | |- | ||
| − | |aspect |3 |aspect ratio 1=4:3, 2=14:9, 3=16:9, 4=5:4, 5=16:10, 6=15:9 | + | |aspect |
| + | |3 | ||
| + | |aspect ratio 1=4:3, 2=14:9, 3=16:9, 4=5:4, 5=16:10, 6=15:9 | ||
|- | |- | ||
| − | |margins|0 0=margins disabled, 1=margins enabled | + | |margins |
| + | |0 | ||
| + | |0=margins disabled, 1=margins enabled | ||
|- | |- | ||
| − | |interlace|0 |0=progressive, 1=interlaced | + | |interlace |
| + | |0 | ||
| + | |0=progressive, 1=interlaced | ||
|- | |- | ||
| − | |rb |0 |0=normal, 1=reduced blanking | + | |rb |
| + | |0 | ||
| + | |0=normal, 1=reduced blanking | ||
|} | |} | ||
<br> | <br> | ||
Revision as of 10:41, 20 February 2019
If you are using Raspberry Pi with the screen, you may encounter incomplete display, with black space around. that would be wrong resolution.
Step 1: Open config.txt
Connect a mouse and a keyboard to your Raspberry Pi. Click open the Terminal, and type in the command to open config.txt
sudo leafpad /boot/config.txt
Step 2: Modify the config.txt file
Now the file config.txt is opened.
1)Define a custom CVT mode add the following lines below #hdmi_force_hotplug=1.
hdmi_cvt=1920 1080 60 3 0 0 0
hdmi_cvt=<width> <height> <framerate> <aspect> <margins> <interlace>
| Value | Default | Default |
| width | (required) | width in pixels |
| height | (required) | height in pixels |
| framerate | (required) | framerate in Hz |
| aspect | 3 | aspect ratio 1=4:3, 2=14:9, 3=16:9, 4=5:4, 5=16:10, 6=15:9 |
| margins | 0 | 0=margins disabled, 1=margins enabled |
| interlace | 0 | 0=progressive, 1=interlaced |
| rb | 0 | 0=normal, 1=reduced blanking |
2)Find the following lines (If there is a "#" mark at the beginning of any of the three lines, which means they are comments, delete the mark. The asterisk "*" represents the value.
hdmi_group=*
hdmi_mode=*
hdmi_drive=*
3)Modify the value, like this:
hdmi_group=2
hdmi_mode=87
....
hdmi_drive=2
hdmi_group=2 means DMT (Display Monitor Timings; the standard typically used by monitors)
hdmi_mode=87 indicates the resolution mode we set before.
hdmi_drive=2 selects the Normal HDMI mode.
For more details about configuring config.txt, refer to Raspberry Pi official website: https://www.raspberrypi.org/documentation/configuration/config-txt.md.
After the modification is done, save, exit then reboot your Raspberry Pi and enjoy.
