Difference between revisions of "Esp8266 Wifi Module"
(→Resource) |
|||
(41 intermediate revisions by the same user not shown) | |||
Line 1: | Line 1: | ||
− | = | + | =Introduction= |
− | + | ||
[[File:Esp8266 and pin .png]]<br> | [[File:Esp8266 and pin .png]]<br> | ||
ESP8266 is an UART-WiFi transparent transmission module with ultralow power consumption, specially designed for the needs of a new connected world. It offers a complete and self-contained Wi-Fi networking solution, allowing it to either host the application or to offload all Wi-Fi networking functions from another application processor.<br> | ESP8266 is an UART-WiFi transparent transmission module with ultralow power consumption, specially designed for the needs of a new connected world. It offers a complete and self-contained Wi-Fi networking solution, allowing it to either host the application or to offload all Wi-Fi networking functions from another application processor.<br> | ||
ESP8266 has powerful on-board processing and storage capabilities that allow it to be integrated with the sensors and other application specific devices through its GPIOs with minimal development up-front and minimal loading during runtime. Its high degree of on-chip integration allows for minimal external circuitry, and the entire solution, including front-end module, is designed to occupy minimal PCB area. ESP8266 Serial Wifi Wireless Transceiver Module is suitable for Uno, Mega 2560 and Nano.<br> | ESP8266 has powerful on-board processing and storage capabilities that allow it to be integrated with the sensors and other application specific devices through its GPIOs with minimal development up-front and minimal loading during runtime. Its high degree of on-chip integration allows for minimal external circuitry, and the entire solution, including front-end module, is designed to occupy minimal PCB area. ESP8266 Serial Wifi Wireless Transceiver Module is suitable for Uno, Mega 2560 and Nano.<br> | ||
− | = | + | |
− | + | =Pin Functions= | |
+ | |||
{| border="1" class="wikitable" | {| border="1" class="wikitable" | ||
!scope="col" |Pin | !scope="col" |Pin | ||
Line 13: | Line 13: | ||
|1 | |1 | ||
|TXD | |TXD | ||
− | | | + | |1) UART_TXD, sending;<br> |
− | + | 2) General Purpose Input/Output:GPIO1;<br> | |
− | + | 3) Pull-down is not allowed when startup;<br> | |
|- | |- | ||
|2 | |2 | ||
Line 23: | Line 23: | ||
|3 | |3 | ||
|CU_PD | |CU_PD | ||
− | | | + | |1) Working at high level;<br> |
− | + | 2) Power off when low level is supplied <br> | |
|- | |- | ||
|4 | |4 | ||
|GPIO2 | |GPIO2 | ||
− | | | + | |1) It should be high level when power on, hardware pull-down is not allowed;<br> |
− | + | 2) Pull-up by default; | |
|- | |- | ||
|5 | |5 | ||
Line 37: | Line 37: | ||
|6 | |6 | ||
|GPIO0 | |GPIO0 | ||
− | | | + | |1) WiFi Status indicator; <br> |
− | + | 2) Operation mode selection:<br> | |
Pull-up: Flash Boot, operation mode <br> | Pull-up: Flash Boot, operation mode <br> | ||
Pull-down: UART Download, download mode | Pull-down: UART Download, download mode | ||
Line 48: | Line 48: | ||
|8 | |8 | ||
|RXD | |RXD | ||
− | | | + | |1) UART_RXD,Receiving<br> |
− | + | 2) General Purpose Input/Output: GPIO3; | |
|} | |} | ||
− | + | ||
− | = | + | =Schematic= |
[[File:Esp8266 schematic.png]] | [[File:Esp8266 schematic.png]] | ||
− | + | ||
− | = | + | =Features= |
• 802.11 b/g/n<br> | • 802.11 b/g/n<br> | ||
• Integrated low power 32-bit MCU<br> | • Integrated low power 32-bit MCU<br> | ||
Line 77: | Line 77: | ||
=How to Test and Debug Esp8266= | =How to Test and Debug Esp8266= | ||
− | ==''' | + | =='''Use Arduino Board'''== |
+ | |||
+ | In this experiment, you will learn same simple operations about ESP8266 – transfer the data collected from sensors to devicebit.com.<br> | ||
+ | '''Introduction to DeviceBit Platform'''<br> | ||
+ | |||
+ | The DeviceBit platform (http://www.devicebit.com/home/publicsensors) is a real-time data brokerage platform for the Internet of Things (IoT), providing most of its functionality via its Application Programming Interface (API). It is quick and easy to add Devices and Applications to the DeviceBit platform. It provides real-time data storage and remote control at scale. The DeviceBit platform is not just an easy way to prototype new Internet-enabled sensors; it's also a service that helps companies bring products to market at scale.<br> | ||
+ | The DeviceBit platform provides basic data analysis tools for rapid data evaluation, as well as real-time alerts and notifications if sensors report “abnormal” conditions.<br> | ||
+ | You can realize your own ideas and develop your own devices relying on this platform. You can focus on hardware instead of software infrastructure.<br> | ||
+ | The DeviceBit platform also communicates with existing social network, such as Twitter and Facebook, allowing you to share what you do with your friend, which might be very helpful to their research on similar field.<br> | ||
+ | '''Operate on DeviceBit Platform''' | ||
+ | |||
+ | Log in on the website (http://www.devicebit.com/). Click Sign Up on the top right corner of the page. <br> | ||
+ | |||
+ | The following page will appear, enter your username, password, and Email. Then log into your mailbox to activate your account.<br> | ||
+ | |||
+ | [[File:Login.jpg]]<br> | ||
+ | |||
+ | '''Add a New Device''' | ||
+ | |||
+ | Log in to your account,then go to User Center, and go to My Devices -> Devices -> Add A device.<br> | ||
+ | [[File:Add device.png]]<br> | ||
+ | Fill in the related information and then click Save.<br> | ||
+ | The related parameters are explained as follows:<br> | ||
+ | 1) ID: The ID of the device, allocated by system automatically. It is unique for each device.<br> | ||
+ | 2) Type: The type of the device. Click the inverted triangle and the following options will appear.<br> | ||
+ | Arduino: Arduino Board.<br> | ||
+ | Lw-board: The board developed by DeviceBit.<br> | ||
+ | Other: Other boards.<br> | ||
+ | 3) Name: The name of the device. For example, Smart Home<br> | ||
+ | 4) Description: Description of the device.<br> | ||
+ | 5) Public: If your devices are public, other users can also view them and their measurement.<br> | ||
+ | 6) Location: The location of your device. Click the location point on the Map.<br> | ||
+ | |||
+ | '''Add a New Sensor''' | ||
+ | |||
+ | The next step is to add a new sensor connected to your device.<br> | ||
+ | Go to My Devices -> Sensors&Controllers -> Sensors, and then click Add to create a new sensor.<br> | ||
+ | |||
+ | [[File:Sensor add.png]]<br> | ||
+ | |||
+ | Now, the following page will appear:<br> | ||
+ | |||
+ | [[File:Add sensor.png]] <br> | ||
+ | |||
+ | Fill in the related information and then click Save.<br> | ||
+ | The related parameters are explained as follows:<br> | ||
+ | 1) ID: The ID of the new sensor. It is unique for each sensor.<br> | ||
+ | 2) Type: The type of the new sensor.<br> | ||
+ | 3) Unit: The unit of the measurement.<br> | ||
+ | 4) Device: Select the device which the sensor is to be connected to.<br> | ||
+ | 5) Name: The name of the new sensor.<br> | ||
+ | 6) Data Conversion: To calibrate your sensor’s measurement. You can enter Coefficient and Offset if applicable.<br> | ||
+ | 7) Picture: Upload the picture of your sensor.<br> | ||
+ | 8) Public: If your sensors are public, other users can also view them and their measurement.<br> | ||
+ | 9) Normal range: The normal range of the sensor’s measurement. You can set it according to your actual need.<br> | ||
+ | 10) Overrange alarm: Turn it on and you will receive the alert by SMS or email when the sensor’s measurement is out of the range.<br> | ||
+ | 11) Data post period: The system indicates that the sensor is OFFLINE if it does not get the data posted by the sensor within every data post period set here.<br> | ||
+ | 12) Remark: Remark of the sensor.<br> | ||
+ | Here we use a photoresistor to collect data and then transfer them to the platform. Add a sensor now. Remember to save every time after you finish filling in the information.<br> | ||
+ | |||
+ | [[File:Light1.png]] | ||
+ | |||
+ | '''Components'''<br> | ||
+ | -1 * ESP8266 Module<br> | ||
+ | -1 * Arduino Board<br> | ||
+ | -1 * Several jump wires<br> | ||
+ | -1 * Breadboard<br> | ||
+ | -1 * USB Cable<br> | ||
+ | - 1* sensor Module<br> | ||
+ | '''Experimental principle'''<br> | ||
+ | SunFounder Uno collects light data by photoresistor, and then uploads the data to network server. Here we use the third party server www.devicebit.com. <br> | ||
+ | Some functions in the code:<br> | ||
+ | ESP_Begin(unsigned long baudRate): Set the communication baud rate between the ESP8266 module and SunFounder Mega2560 as 115200 (In esptodevicebit library provided, the communication baud rate between the ESP8266 module and SunFounder Mega 2560 currently only support 115200.).<br> | ||
+ | ESP_Init(): ESP8266 module initilization configuration.<br> | ||
+ | ESP_Send(String server, String gateWay, String userKey, String name, String value): The sending function of the ESP8266 module. Its parameters are decided by the DeviceBit platform. Server is the IP address of sending website (For example, www.devicebit.com we used); gateWay is a gateway number for a user, and you can get it from User Center of the DeviceBit platform; UserKey is obtained from User Center of the DeviceBit platform; Name is the name of the sensor you upload, which is named by you on the DeviceBit platform; Value is the data from the sensor you upload, and it should be of string type.<br> | ||
+ | '''Experimental Procedures'''<br> | ||
+ | Step1: Connect the circuit<br> | ||
+ | {| border="1" class="wikitable" | ||
+ | |ESP8266 | ||
+ | |Mega2560 | ||
+ | |- | ||
+ | |TXD | ||
+ | |Pin 19(RX1) | ||
+ | |- | ||
+ | |RXD | ||
+ | |Pin 18(TX1) | ||
+ | |- | ||
+ | |CH_PD | ||
+ | |3.3V | ||
+ | |- | ||
+ | |GND | ||
+ | |GND | ||
+ | |- | ||
+ | |VCC | ||
+ | |3.3V | ||
+ | |} | ||
+ | [[File:Esp8266mega2560.png]] | ||
+ | |||
+ | SIG of sensor Module connect to A5, VCC to 5V, GND to GND.<br> | ||
+ | |||
+ | Step2: Open [http://wiki.sunfounder.cc/images/9/96/Esp_devicebit.zip esp_ devicebit].Before upload, you need to change some parameters. <br> | ||
+ | 1) Change the SSID and password into your own ones (see Line 8 and 9).<br> | ||
+ | |||
+ | [[File:Juhao.png]]<br> | ||
+ | |||
+ | 2) You need to know your password on Devicebit. Go to User Center, click My Account ->Account Settings, and then you can see your Userkey. <br> | ||
+ | |||
+ | [[File:Userkeyuoi.png]]<br> | ||
+ | |||
+ | Copy and paste the value of Userkey in the following code. The gateway number is your device ID on the Devicebit platform. You can click MyDevices ->Devices in User Center. Select your device ID (here the device is Smart Home, and ID: 01)<br> | ||
+ | |||
+ | [[File:Arduino01.png]]<br> | ||
+ | [[File:Userkey andga.png]] <br> | ||
+ | |||
+ | and then download it to the SunFounder Mega 2560 board.<br> | ||
+ | Experimental phenomenon: Open the serial monitor, it will display configuration information about ESP8266. <br> | ||
+ | |||
+ | [[File:Light1 Value.png]]<br> | ||
+ | |||
+ | Login to www.devicebit.com, enter into your homepage, check sensor data, and you will see light data uploaded from the Gateway shield<br> | ||
+ | |||
+ | [[File:Devicebit light1.png]]<br> | ||
+ | |||
+ | <font color="red">Note: if you use a uno board, before you upload the code, you need to modify the line 6 #define MEGA2560 to #define UNO in the esp8266.h</font><br> | ||
+ | |||
+ | [[File:Uno12.png]]<br> | ||
+ | |||
+ | And connect RXD to Pin 3 , TXD to pin 2 <br> | ||
+ | |||
+ | [[File:Uno esp8266.png]]<br> | ||
+ | |||
+ | =='''Use AT Command'''== | ||
+ | |||
+ | '''Preparation''' | ||
-1 * PL2303HXD<br> | -1 * PL2303HXD<br> | ||
Line 83: | Line 216: | ||
-1 * ESP8266<br> | -1 * ESP8266<br> | ||
− | + | '''Procedures''' | |
− | + | Step 1: wire | |
− | Connect UTXD of ESP8266 to RXD of PL2303, URXD to TXD, CH_PD to 5v, GND to GND, and VCC to 3.3v. The Uno board here is used to supply 3.3v power. PL2303 is a USB to Serial Bridge Controller. You can also use other components, such as FTDI.<br> | + | Connect UTXD of ESP8266 to RXD of PL2303, URXD to TXD, CH_PD to 5v(recommend 3.3v), GND to GND, and VCC to 3.3v. The Uno board here is used to supply 3.3v power. PL2303 is a USB to Serial Bridge Controller. You can also use other components, such as FTDI.<br> |
− | + | ||
[[File:CONNECT.jpeg]]<br> | [[File:CONNECT.jpeg]]<br> | ||
− | + | ||
− | + | ||
+ | Step 2:set parameters | ||
After wiring, open the serial port debug tool sscom32. Set parameters at first.<br> | After wiring, open the serial port debug tool sscom32. Set parameters at first.<br> | ||
1) Open the serial port, click Open Com. Select the correct port, as shown below. | 1) Open the serial port, click Open Com. Select the correct port, as shown below. | ||
− | + | ||
[[File:Ssc4.png]]<br> | [[File:Ssc4.png]]<br> | ||
− | + | ||
2) Select the correct baud rate. Here select 115200 bps. Click SendNew, as shown below. | 2) Select the correct baud rate. Here select 115200 bps. Click SendNew, as shown below. | ||
− | + | ||
[[File:Ssc3.png]]<br> | [[File:Ssc3.png]]<br> | ||
− | + | ||
− | + | Step3:AT instructions | |
Now, you can start to send instructions. Enter "AT+RST" in the text box. It’s used to restart the module. If ESP8266 goes well, OK will be sent, as shown below: | Now, you can start to send instructions. Enter "AT+RST" in the text box. It’s used to restart the module. If ESP8266 goes well, OK will be sent, as shown below: | ||
− | + | ||
[[File:Ssc2.png]]<br> | [[File:Ssc2.png]]<br> | ||
− | + | ||
You can also send other instructions, such as "AT+GMR". It is used to check the version of AT commands and SDK that you are using, the type of which is "executed". | You can also send other instructions, such as "AT+GMR". It is used to check the version of AT commands and SDK that you are using, the type of which is "executed". | ||
− | + | ||
[[File:Ssc1.png]]<br> | [[File:Ssc1.png]]<br> | ||
− | + | ||
− | For more information about ESP8266 AT Instructions. please refer to | + | For more information about ESP8266 AT Instructions. please refer to [http://wiki.sunfounder.cc/images/3/3e/ESP8266EX_AT_Instruction_Set.pdf ESP8266EX_AT_Instruction_Set]. |
− | + | ||
− | [http:// | + | =Resource= |
− | [http:// | + | [http://wiki.sunfounder.cc/images/9/96/Esp_devicebit.zip Esp_devicebit][[File:ZIP.jpg]]<br> |
− | [http:// | + | [http://wiki.sunfounder.cc/images/3/3e/ESP8266EX_AT_Instruction_Set.pdf ESP8266EX_AT_Instruction_Set][[File:PDF.jpg]]<br> |
− | [http:// | + | [http://wiki.sunfounder.cc/images/8/8a/0a-esp8266ex_datasheet_en.pdf ESP8266_Module_User_Guide][[File:PDF.jpg]]<br> |
+ | [http://wiki.sunfounder.cc/images/b/b2/Sscom32E.zip Sscom32E][[File:ZIP.jpg]] |
Latest revision as of 08:13, 9 October 2017
Contents
Introduction
ESP8266 is an UART-WiFi transparent transmission module with ultralow power consumption, specially designed for the needs of a new connected world. It offers a complete and self-contained Wi-Fi networking solution, allowing it to either host the application or to offload all Wi-Fi networking functions from another application processor.
ESP8266 has powerful on-board processing and storage capabilities that allow it to be integrated with the sensors and other application specific devices through its GPIOs with minimal development up-front and minimal loading during runtime. Its high degree of on-chip integration allows for minimal external circuitry, and the entire solution, including front-end module, is designed to occupy minimal PCB area. ESP8266 Serial Wifi Wireless Transceiver Module is suitable for Uno, Mega 2560 and Nano.
Pin Functions
Pin | Name | Description |
---|---|---|
1 | TXD | 1) UART_TXD, sending; 2) General Purpose Input/Output:GPIO1; |
2 | GND | GND |
3 | CU_PD | 1) Working at high level; 2) Power off when low level is supplied |
4 | GPIO2 | 1) It should be high level when power on, hardware pull-down is not allowed; 2) Pull-up by default; |
5 | GPIO16 | External Reset signal, reset when low level is supplied; work when high level is supplied (high level by default); |
6 | GPIO0 | 1) WiFi Status indicator; 2) Operation mode selection: |
7 | VCC | Power Supply(3.3V) |
8 | RXD | 1) UART_RXD,Receiving 2) General Purpose Input/Output: GPIO3; |
Schematic
Features
• 802.11 b/g/n
• Integrated low power 32-bit MCU
• Integrated 10-bit ADC
• Integrated TCP/IP protocol stack
• Integrated TR switch, balun, LNA, power amplifier and matching network
• Integrated PLL, regulators, and power management units
• Supports antenna diversity
• Wi-Fi 2.4 GHz, support WPA/WPA2
• Support STA/AP/STA+AP operation modes
• Support Smart Link Function for both Android and iOS devices
• SDIO 2.0, (H) SPI, UART, I2C, I2S, IR Remote Control, PWM, GPIO
• A-MPDU & A-MSDU aggregation & 0.4s guard interval
• Deep sleep power <10uA, Power down leakage current < 5uA
• Wake up and transmit packets in < 2ms
• Standby power consumption of < 1.0mW (DTIM3)
• +20 dBm output power in 802.11b mode
• Operating temperature range -40C ~ 125C
• FCC, CE, TELEC, Wi-Fi Alliance, and SRRC certified
How to Test and Debug Esp8266
Use Arduino Board
In this experiment, you will learn same simple operations about ESP8266 – transfer the data collected from sensors to devicebit.com.
Introduction to DeviceBit Platform
The DeviceBit platform (http://www.devicebit.com/home/publicsensors) is a real-time data brokerage platform for the Internet of Things (IoT), providing most of its functionality via its Application Programming Interface (API). It is quick and easy to add Devices and Applications to the DeviceBit platform. It provides real-time data storage and remote control at scale. The DeviceBit platform is not just an easy way to prototype new Internet-enabled sensors; it's also a service that helps companies bring products to market at scale.
The DeviceBit platform provides basic data analysis tools for rapid data evaluation, as well as real-time alerts and notifications if sensors report “abnormal” conditions.
You can realize your own ideas and develop your own devices relying on this platform. You can focus on hardware instead of software infrastructure.
The DeviceBit platform also communicates with existing social network, such as Twitter and Facebook, allowing you to share what you do with your friend, which might be very helpful to their research on similar field.
Operate on DeviceBit Platform
Log in on the website (http://www.devicebit.com/). Click Sign Up on the top right corner of the page.
The following page will appear, enter your username, password, and Email. Then log into your mailbox to activate your account.
Add a New Device
Log in to your account,then go to User Center, and go to My Devices -> Devices -> Add A device.
Fill in the related information and then click Save.
The related parameters are explained as follows:
1) ID: The ID of the device, allocated by system automatically. It is unique for each device.
2) Type: The type of the device. Click the inverted triangle and the following options will appear.
Arduino: Arduino Board.
Lw-board: The board developed by DeviceBit.
Other: Other boards.
3) Name: The name of the device. For example, Smart Home
4) Description: Description of the device.
5) Public: If your devices are public, other users can also view them and their measurement.
6) Location: The location of your device. Click the location point on the Map.
Add a New Sensor
The next step is to add a new sensor connected to your device.
Go to My Devices -> Sensors&Controllers -> Sensors, and then click Add to create a new sensor.
Now, the following page will appear:
Fill in the related information and then click Save.
The related parameters are explained as follows:
1) ID: The ID of the new sensor. It is unique for each sensor.
2) Type: The type of the new sensor.
3) Unit: The unit of the measurement.
4) Device: Select the device which the sensor is to be connected to.
5) Name: The name of the new sensor.
6) Data Conversion: To calibrate your sensor’s measurement. You can enter Coefficient and Offset if applicable.
7) Picture: Upload the picture of your sensor.
8) Public: If your sensors are public, other users can also view them and their measurement.
9) Normal range: The normal range of the sensor’s measurement. You can set it according to your actual need.
10) Overrange alarm: Turn it on and you will receive the alert by SMS or email when the sensor’s measurement is out of the range.
11) Data post period: The system indicates that the sensor is OFFLINE if it does not get the data posted by the sensor within every data post period set here.
12) Remark: Remark of the sensor.
Here we use a photoresistor to collect data and then transfer them to the platform. Add a sensor now. Remember to save every time after you finish filling in the information.
Components
-1 * ESP8266 Module
-1 * Arduino Board
-1 * Several jump wires
-1 * Breadboard
-1 * USB Cable
- 1* sensor Module
Experimental principle
SunFounder Uno collects light data by photoresistor, and then uploads the data to network server. Here we use the third party server www.devicebit.com.
Some functions in the code:
ESP_Begin(unsigned long baudRate): Set the communication baud rate between the ESP8266 module and SunFounder Mega2560 as 115200 (In esptodevicebit library provided, the communication baud rate between the ESP8266 module and SunFounder Mega 2560 currently only support 115200.).
ESP_Init(): ESP8266 module initilization configuration.
ESP_Send(String server, String gateWay, String userKey, String name, String value): The sending function of the ESP8266 module. Its parameters are decided by the DeviceBit platform. Server is the IP address of sending website (For example, www.devicebit.com we used); gateWay is a gateway number for a user, and you can get it from User Center of the DeviceBit platform; UserKey is obtained from User Center of the DeviceBit platform; Name is the name of the sensor you upload, which is named by you on the DeviceBit platform; Value is the data from the sensor you upload, and it should be of string type.
Experimental Procedures
Step1: Connect the circuit
ESP8266 | Mega2560 |
TXD | Pin 19(RX1) |
RXD | Pin 18(TX1) |
CH_PD | 3.3V |
GND | GND |
VCC | 3.3V |
SIG of sensor Module connect to A5, VCC to 5V, GND to GND.
Step2: Open esp_ devicebit.Before upload, you need to change some parameters.
1) Change the SSID and password into your own ones (see Line 8 and 9).
2) You need to know your password on Devicebit. Go to User Center, click My Account ->Account Settings, and then you can see your Userkey.
Copy and paste the value of Userkey in the following code. The gateway number is your device ID on the Devicebit platform. You can click MyDevices ->Devices in User Center. Select your device ID (here the device is Smart Home, and ID: 01)
and then download it to the SunFounder Mega 2560 board.
Experimental phenomenon: Open the serial monitor, it will display configuration information about ESP8266.
Login to www.devicebit.com, enter into your homepage, check sensor data, and you will see light data uploaded from the Gateway shield
Note: if you use a uno board, before you upload the code, you need to modify the line 6 #define MEGA2560 to #define UNO in the esp8266.h
And connect RXD to Pin 3 , TXD to pin 2
Use AT Command
Preparation
-1 * PL2303HXD
-1 * SunFounder Uno Board
-1 * ESP8266
Procedures
Step 1: wire
Connect UTXD of ESP8266 to RXD of PL2303, URXD to TXD, CH_PD to 5v(recommend 3.3v), GND to GND, and VCC to 3.3v. The Uno board here is used to supply 3.3v power. PL2303 is a USB to Serial Bridge Controller. You can also use other components, such as FTDI.
Step 2:set parameters
After wiring, open the serial port debug tool sscom32. Set parameters at first.
1) Open the serial port, click Open Com. Select the correct port, as shown below.
2) Select the correct baud rate. Here select 115200 bps. Click SendNew, as shown below.
Step3:AT instructions Now, you can start to send instructions. Enter "AT+RST" in the text box. It’s used to restart the module. If ESP8266 goes well, OK will be sent, as shown below:
You can also send other instructions, such as "AT+GMR". It is used to check the version of AT commands and SDK that you are using, the type of which is "executed".
For more information about ESP8266 AT Instructions. please refer to ESP8266EX_AT_Instruction_Set.
Resource
Esp_devicebit
ESP8266EX_AT_Instruction_Set
ESP8266_Module_User_Guide
Sscom32E