Difference between revisions of "2 Channel 5V Relay Module"

Revision as of 06:40, 18 September 2016

Features

• Relay Maximum output: DC 30V/10A, AC 250V/10A

• 2 Channel Relay Module with Optocoupler High Level Triger expansion board, which is compatible with arduino and Raspberry Pi

• Standard interface that can be controlled directly by microcontroller ( 8051,AVR, *PIC, DSP, ARM, ARM, MSP430, TTL logic)

• Relay of high quality loose music relays SPDT. A common terminal, a normally open, one normally closed terminal

• optocoupler isolation, good anti-jamming

Introduction

This is a 5V 2-channel relay interface board, and each channel needs a 15-20mA driver current. It can be used to control various appliances and equipment with large current. It is equiped with high-current relays that work under AC250V 10A or DC30V 10A. It has a standard interface that can be controlled directly by microcontroller.

Schematic

principle

See the picture below: A is an electromagnet, B armature, C spring, D moving contact, and E fixed contacts. There are two fixed contacts, a normally closed one and a normally open one. When the coil is not energized, the normally open contact is the one that is off, while the normally closed one is the other that is on.

Add a certain voltage to the coil and some currents will pass through the coil thus generating the electromagnetic effect. So the armature overcomes the tension of the spring and is attracted to the core, thus closing the moving contact of the armature and the normally open contact (or you may say releasing the former and the normally closed contact). After the coil is de-energized, the electromagnetic force disappears and the armature moves back to the original position, releasing the moving contact and normally closed contact. The closing and releasing of the contacts results in power on and off of the circuit.

Input:

DC+: Connected to positive supply voltage (supply power according to relay voltage)

DC-: Connected to negative supply voltage

IN1: Signal triggering terminal 1 of relay module

IN2: Signal triggering terminal 2 of relay module

Output:

Each submodular of the relay has one NC(nomalclose), one NO(nomalopen) and one COM(Common). So there are 2 NC, 2 NO and 2 COM of the channel relay in total. NC stands for the normal close port contact and the state without power; No stands for the normal open port contact and the state with power. COM means the common port. You can choose NC port or NO port according to whether power or not.

Application

General purpose

Testing Experiment

Experiment Principle:

When a low level is supplied to signal terminal of the 2-channel relay, the LED at the output terminal will light up. Otherwise, it will turn off. If a periodic high and low level is supplied to the signal terminal, you can see the LED will cycle between on and off.

For Arduino：

Step 1：

Connect the signal terminal IN1、IN2 of 2-channel relay to digital port 4、5 of the SunFounder Arduino ATMega2560 board, and connect an LED at the output terminal.（Pay attention to that there are only two submodules of the 8-channel relay are used in this example, but you can use the 2 submodules freely.）

8-channel relay--------------- Arduino ATMega2560

IN1------------------------ 4

IN2------------------------ 5

Step 2:

Run the companion procedures text_code of the SunFounder Arduino ATMega2560 board，Please see the source code in Resources at the end of the page.Then you can see the LED cycle between on and off.

The actual figure is shown below:

For raspberry pi

Step1:

Connect the signal terminal IN2、IN1 of 2-channel relay to port 17、18 of the Raspberry Pi, and connect an LED at the output terminal.

2-channel relay------------ Raspberry Pi

IN2----------------------- 17

IN1----------------------- 18

Step 2:

Run the test_code,Please see the source code in Resources at the end of the page. Then you can see the LED cycle between on and off.

The actual figure is shown below：

Component List

1 x 2 Channel Relay Module

Resources

Code for Arduino ATMega2560:

2_test_code_for_arduino_atmega2560
Code for Raspberry Pi :

2_test_code_for_raspberry_pi