Difference between revisions of "Flame sensor Module"
(Created page with "=='''Introduction'''== A flame sensor module that consists of a flame sensor, resistor, capacitor, potentiometer, and comparator LM393 in an integrated circuit. It can detect...") |
(→Resource) |
||
| (7 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
=='''Introduction'''== | =='''Introduction'''== | ||
A flame sensor module that consists of a flame sensor, resistor, capacitor, potentiometer, and comparator LM393 in an integrated circuit. It can detect infrared light with a wavelength ranging from 700nm to 1000nm.The far-infrared flame probe converts the strength changes of the external infrared light into current changes.<br> | A flame sensor module that consists of a flame sensor, resistor, capacitor, potentiometer, and comparator LM393 in an integrated circuit. It can detect infrared light with a wavelength ranging from 700nm to 1000nm.The far-infrared flame probe converts the strength changes of the external infrared light into current changes.<br> | ||
| − | [[File:Flame sensor1.png]] | + | [[File:Flame sensor1.png]]<br> |
| − | The schematic diagram of the module is as follows: | + | The schematic diagram of the module is as follows:<br> |
[[File:Flame sensor2.png]] | [[File:Flame sensor2.png]] | ||
| + | |||
=='''Features'''== | =='''Features'''== | ||
1) Equipped with power light and a signal output indicator<br> | 1) Equipped with power light and a signal output indicator<br> | ||
| Line 17: | Line 18: | ||
It is applicable to all kinds of flame and can be used for fire detection (e.g. flame alarm). | It is applicable to all kinds of flame and can be used for fire detection (e.g. flame alarm). | ||
| − | ==''' | + | =='''Resource'''== |
| − | - | + | [https://www.sunfounder.com/learn/Sensor-Kit-v2-0-for-Arduino/lesson-9-flame-alarm-sensor-kit-v2-0-for-arduino.html Flame Sensor Experiment for Arduino][[File:LINK.jpg]]<br> |
| − | - | + | [https://www.sunfounder.com/learn/sensor-kit-v2-0-for-raspberry-pi-b-plus/lesson-21-flame-sensor-sensor-kit-v2-0-for-b-plus.html Flame Sensor Experiment for Raspberry Pi][[File:LINK.jpg]] |
| − | - | + | |
| − | - | + | |
| − | - | + | |
| − | - | + | |
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | [[File: | + | |
| − | + | ||
| − | [ | + | |
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | [[File: | + | |
Latest revision as of 02:56, 4 July 2016
Contents
Introduction
A flame sensor module that consists of a flame sensor, resistor, capacitor, potentiometer, and comparator LM393 in an integrated circuit. It can detect infrared light with a wavelength ranging from 700nm to 1000nm.The far-infrared flame probe converts the strength changes of the external infrared light into current changes.
The schematic diagram of the module is as follows:
Features
1) Equipped with power light and a signal output indicator
2) Support a detection angle of appr. 60 degrees; particularly sensitive to flame spectrum.
3) Contain an adjustable precision potentiometer for sensitivity adjustment .
4) With a comparator LM393 to output both digital and analog signals at the same time
5) Connected directly with I/O port of MCU, needless of external circuit
6) Sensitive to flame, also responsive to general light; generally used for flame
7) Detect flame or light of a wavelength ranging from 760 to 1100 nm.
8) Output clean signals by a comparator, with good waveform and driving capability as strong as more than 15mA
9) Working voltage: 3.3V - 5V; PCB size: 2.3 x 2.3 cm
Application
It is applicable to all kinds of flame and can be used for fire detection (e.g. flame alarm).
Resource
Flame Sensor Experiment for Arduino
Flame Sensor Experiment for Raspberry Pi
