View source for 2 Channel 5V Relay Module

=='''Introduction'''==
[[File:2cha1.jpg]]<br>
This is a LOW Level 5V 2-channel relay interface board, and each channel needs a 15-20mA driver current. It can be used to control various appliances and equipment with large current. It is equiped with high-current relays that work under AC250V 10A or DC30V 10A. It has a standard interface that can be controlled directly by microcontroller.


=='''Features'''==

*Relay Maximum output: DC 30V/10A, AC 250V/10A
*2 Channel Relay Module with Optocoupler LOW Level Triger expansion board, which is compatible with arduino 
*Standard interface that can be controlled directly by microcontroller ( 8051, AVR, *PIC, DSP, ARM, ARM, MSP430, TTL logic)
*Relay of high quality loose music relays SPDT. A common terminal, a normally open, one normally closed terminal
*optocoupler isolation, good anti-jamming



=='''Schematic'''==
VCC and RY-VCC are also the power supply of the relay module. When you need to drive a large power load, you can take the jumper cap off and connect an extra power to RY-VCC to supply the relay; connect VCC to 5V of the MCU board to supply input signals.<br> 


[[File:2cha2.jpg]]

=='''principle'''==
See the picture below: A is an electromagnet, B armature, C spring, D moving contact, and E fixed contacts. There are two fixed contacts, a normally closed one and a normally open one. When the coil is not energized, the normally open contact is the one that is off, while the normally closed one is the other that is on.         

[[File:2cha3.jpg]]

Add a certain voltage to the coil and some currents will pass through the coil thus generating the electromagnetic effect. So the armature overcomes the tension of the spring and is attracted to the core, thus closing the moving contact of the armature and the normally open contact (or you may say releasing the former and the normally closed contact). After the coil is de-energized, the electromagnetic force disappears and the armature moves back to the original position, releasing the moving contact and normally closed contact. The closing and releasing of the contacts results in power on and off of the circuit.

==='''Input:'''===
VCC : Connected to positive supply voltage (supply power according to relay voltage)<br>
GND : Connected to negative supply voltage<br>
IN1: Signal triggering terminal 1 of relay module<br>
IN2: Signal triggering terminal 2 of relay module<br>


==='''Output:'''===
Each submodular of the relay has one NC(nomalclose), one NO(nomalopen) and one COM(Common). So there are 2 NC, 2 NO and 2 COM of the channel relay in total. NC stands for the normal close port contact and the state without power; No stands for the normal open port contact and the state with power. COM means the common port. You can choose NC port or NO port according to whether power or not. 

=='''Application'''==
General purpose

=='''Testing Experiment'''==
'''Experiment Principle:'''

When a low level is supplied to signal terminal of the 2-channel relay, the LED at the output terminal will light up. Otherwise, it will turn off. If a periodic high and low level is supplied to the signal terminal, you can see the LED will cycle between on and off.

==='''For Arduino：'''===
'''Step 1：'''

Connect the signal terminal IN1、IN2 of 2-channel relay to digital port 4、5 of the SunFounder Arduino ATMega2560 board, and connect an LED at the output terminal.

::::::::::2 channel relay---------------Arduino ATMega2560
:::::::::::IN1------------------------	4
:::::::::::IN2------------------------	5

'''Step 2:'''

Run the companion procedures text_code of the SunFounder Arduino ATMega2560 board，Please see the source code in Resources at the end of the page.Then you can see the LED cycle between on and off.

The actual figure is shown below:

[[File:2cha4.jpg]]

==='''For raspberry pi'''===

'''Step1:'''

Connect the signal terminal IN2、IN1 of 2-channel relay to port 17、18 of the Raspberry Pi, and connect an LED at the output terminal. 

:::::::::::2-channel relay-----------------Raspberry Pi 
::::::::::::::IN2-----------------------17
::::::::::::::IN1-----------------------18

'''Step2:'''<br>
Please see the source code in Resources at the end of the page.Download the file：
 pi@raspberrypi:~ $ wget https://www.sunfounder.com/wiki/images/d/d6/2_test_code_for_raspberry_pi.zip

'''Step3:'''<br>
Unzip the file:
 pi@raspberrypi:~ $ unzip 2_test_code_for_raspberry_pi.zip

'''Step4:'''<br>
Run the code:
 pi@raspberrypi:~ $ python 2_channel_relay.py

After run the test_code, Then you can see the LED cycle between on and off.

The actual figure is shown below：

[[File:2cha5.jpg]]

=='''Resources'''==
Code for Arduino:

[https://www.sunfounder.com/wiki/index.php?title=File:2_channel_relay.zip 2_channel_relay][[File:ZIP.jpg]]<br>
Code for Raspberry Pi :

[https://www.sunfounder.com/wiki/index.php?title=File:2_test_code_for_raspberry_pi.zip 2_test_code_for_raspberry_pi][[File:ZIP.jpg]]<br>