View source for 2.2 Inch TFT Screen Display Extension Board

[[File:TFT1.jpg]]

===Features===

*Size: 65mm×56.5mm, standard as a Raspberry Pi HAT board
*Screen sizing 2.2 inch and supporting a 320x240 resolution with high PPI, being small but able to provide a fine image
*Multi-button design: 6 buttons, meeting different demands for buttons from various users
*With an Infrared receiver

===Procedures for Applying TFT Screen Display with Raspbian Jessie===

[[File:TFT2.jpg]]

'''Download''' the simplified installation package at the bottom (or [https://www.sunfounder.com/wiki/index.php?title=File:Pitft_setup.tar.zip here]). Transfer it to the Raspberry Pi.

Finish the installation with '''Installation Guide''' which comes along with the product.

===Buttons===

[[File:TFT3.jpg]]

There are 6 buttons on the screen, which are marked by a number beginning with "#", such as '''#21''', '''#22''', etc. The number indicates that the pins are connected to GPIOs defined by '''BCM''' numbering.

===Backlight control:===

[[File:TFT6.jpg]]

'''SJ2''' is the switch for backlight control. Connect the two soldering pads of SJ2 by solder. You can use '''#27''' to switch on/off the backlight.

 gpio -g mode 27 in  # Switch off
 gpio -g mode 27 out # Switch on

===Infrared Receiving:===

[[File:TFT4.jpg]]

'''SJ1''' is the switch for IR control.

1.Connect the two soldering pads of SJ1 by solder.

2. Update and install the LIRC. Run:

 sudo apt-get update
 sudo apt-get install lirc
3.Edit /boot/config.txt and add settings. IR receiver of the extension board = 26<br />
 sudo nano /boot/config.txt<br />
Add the following line to config.txt<br />
 dtoverlay=lirc-rpi,gpio_in_pin=26<br />
4.Edit the configuration file of LIRC to enable the Infrared function:<br />
 sudo nano /etc/lirc/hardware.conf<br />
Change the following lines:<br />
 LIRCD_ARGS="--uinput"
 DRIVER="default"
 DEVICE="/dev/lirc0"
 MODULES="lirc_rpi"
Note that there should be two hyphens in "--uinput".<br />
5.Reboot the Raspberry Pi.<br />
 sudo reboot<br />
And then, check whether the Infrared function is enabled.<br />
 ls /dev/l*<br />
[[File:TFT5.jpg]]<br />
If you see the contents are displayed as shown in the above red box, it means the function is active now.

6.Record the buttons

 sudo /etc/init.d/lirc stop
 sudo irrecord -n -d /dev/lirc0 ~/lircd.conf

Record the buttons for your remote control as prompted. Record respectively "'''pause'''", "'''nextsong'''", "'''prevsong'''", "'''stop'''", "'''volumeup'''", and "v'''olumedown'''".

Overwrite the corresponding lirc file with the recorded ~/lircd.conf

 sudo cp ~/lircd.conf /etc/lirc/lircd.conf

7.Start lirc

 sudo /etc/init.d/lirc start
8.Check the status of recording. Run

 irw
Then press the buttons recorded before in turns.

9.You can also view the name of the recorded and ready-for-use buttons by the command irsend

 irsend LIST /home/pi/lircd.conf
You can see contents similar to the following displayed

 irsend: 000000000000c837 pause
 irsend: 00000000000048b7 nextsong
10.Now you can send the code of the recorded buttons on the remote by the Infrared emitter. You can thus use the extension board to change programs. Refer to the following commands:

 irsend SEND_ONCE /home/pi/lircd.conf pause
 irsend SEND_ONCE /home/pi/lircd.conf nextsong
 irsend SEND_ONCE /home/pi/lircd.conf KEY_VOLUMEDOWN
 irsend SEND_ONCE /home/pi/lircd.conf KEY_VOLUMEUP

[https://www.sunfounder.com/wiki/index.php?title=File:Pitft_setup.tar.zip Pitft_setup][[File:ZIP.jpg]]