Difference between revisions of "Main Page"
From Wiki
(→Raspberry Pi) |
(→Raspberry Pi) |
||
(38 intermediate revisions by the same user not shown) | |||
Line 10: | Line 10: | ||
|width="32%" valign="top" align="left"| | |width="32%" valign="top" align="left"| | ||
|} | |} | ||
− | === '''Mixly''' === | + | ==== '''Mixly''' ==== |
{| border="0" cellpadding="10" width="100%" | {| border="0" cellpadding="10" width="100%" | ||
Line 16: | Line 16: | ||
|width="32%" valign="top" align="left"| | |width="32%" valign="top" align="left"| | ||
*[[Get started with Mixly]] | *[[Get started with Mixly]] | ||
− | |||
|} | |} | ||
<div id="Arduino"></div> | <div id="Arduino"></div> | ||
+ | |||
=== '''Arduino''' === | === '''Arduino''' === | ||
Line 161: | Line 161: | ||
*[[Line Follower Module]] | *[[Line Follower Module]] | ||
*[[Line Follower Module(5 channel)]] | *[[Line Follower Module(5 channel)]] | ||
+ | *[[MagicKey]] | ||
*[[Mobile Robot Remote Controller]] | *[[Mobile Robot Remote Controller]] | ||
*[[Mercury Switch Module]] | *[[Mercury Switch Module]] | ||
Line 200: | Line 201: | ||
*[[Breadboard Basics – Types]] | *[[Breadboard Basics – Types]] | ||
*[[55g Metal Gear Servo]] | *[[55g Metal Gear Servo]] | ||
+ | *[[SF006C Clutch Gear Digital Servo]] | ||
|} | |} | ||
Line 263: | Line 265: | ||
*[[LCD1602/I2C LCD1602 FAQ]] | *[[LCD1602/I2C LCD1602 FAQ]] | ||
*[[Smart Car Kit for Arduino FAQ]] | *[[Smart Car Kit for Arduino FAQ]] | ||
+ | *[[4DOF Pin correspondence extension board]] | ||
===Raspberry Pi=== | ===Raspberry Pi=== | ||
Line 272: | Line 275: | ||
*[[How to Log in to Raspberry Pi by FT232 Serial to TTL]] | *[[How to Log in to Raspberry Pi by FT232 Serial to TTL]] | ||
*[[Dragit FAQ]] | *[[Dragit FAQ]] | ||
+ | *[[install dragit]] | ||
*[[PiSmart Car FAQ]] | *[[PiSmart Car FAQ]] | ||
+ | *[[PiSmart AI BOX FAQ]] | ||
+ | *[[Raspberry super kit V3 FAQ]] | ||
+ | *[[PiCar FAQ]] | ||
+ | *[[PiCar-V for dragit FAQ]] | ||
+ | *[[Test the PiSmart fuse tutorial]] | ||
+ | *[[Adjust Resolution for Raspberry Pi]] | ||
===Drones/Model Aircrafts=== | ===Drones/Model Aircrafts=== | ||
Line 280: | Line 290: | ||
*[[SF250 FAQ]] | *[[SF250 FAQ]] | ||
*[[6D-BOX FAQ]] | *[[6D-BOX FAQ]] | ||
+ | |} | ||
+ | ===Raspad=== | ||
+ | {| border="0" cellpadding="10" width="100%" | ||
+ | |- | ||
+ | |width="32%" valign="top" align="left"| | ||
+ | *[[Replace HDMI cable tutorial]] | ||
+ | *[[Replace power USB cable tutorial]] | ||
+ | *[[The touch screen does not work properly FAQ]] | ||
+ | *[[Install the fan for Raspad]] | ||
|} | |} |
Revision as of 10:12, 20 February 2019
Getting Started
Mixly
Arduino
Raspberry Pi