IR Remote Controller Configuration for OSMC

From Wiki
Revision as of 07:38, 20 March 2017 by Root (Talk | contribs) (Resource)

(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Jump to: navigation, search

Prepare:

In this guide, the lirc library is used.
Here we use
1. An IR receiver and an IR remote control. (you can get it from www.sunfounder.com)
2. A Raspberry Pi with OSMC.
3. A screen with HDMI port or other ports with a converter to HDMI.
4. A Wi-Fi adapter or a cable to connect your Raspberry Pi to the Internet
5. A PC or a laptop, with Linux, which is connected to the Internet with wire or wirelessly.
Connect the IR receiver like this: (no wire required)

PI1.png

1. Find out the IP address of the Raspberry Pi on OSMC

On OSMC, with your keyboard, go through My OSMCNetworkWire or Wireless.
Then on the right side the IP appears.

2. Log in OSMC via ssh

Open a terminal (T1) on your PC or laptop. Log in OSMC through ssh from another Linux.
'ssh osmc@192.168.0.137 '(Replace the IP address with your own in your OSMC)
PI2.png
Type in yes and press Enter
PI3.png
Type in the password: osmc (Note: Both the user name and password in OSMC is osmc, in lower case)
PI4.png
There you go.

3. Change the pins. Plug a keyboard into your Raspberry Pi

On OSMC, with your keyboard, go through My OSMCPi ConfigHardware Support → -gpio_out_pin, (if there is no –gpio_out_pin in Hardware Support, select Enable LIRC GPIO support and press Enter) and press the key left or right arrow to change it to 23. Then press the down arrow key to turn to -gpio_in_pin, also press left or right to change it to 18 Like this:


|Enable LIRC GPIO support █ |
| -gpio_out_pin 23 |
| -gpio_in_pin 18 |


Select OK and press Enter to confirm.

4. Configure the auto startup of lirc

On your PC or laptop (remote access window):

$ sudo vi /etc/modules

Press the "i" key to enter the edit mode and add the following lines

lirc_dev
lirc_rpi gpio_in_pin=18

Then press "Esc" to exit the edit mode, enter the command to save and exit

:wq

5. Reboot

$ sudo reboot

6. Log in OSMC again via ssh (the IP may change)

$ssh osmc@192.168.0.133

7. Search for the pid of the lirc sever

$pgrep –l lircd

Then the following will be printed:
PI6.png
So the number before lircd is its pid.

8. Kill the licd sever (replace "290" below with the pid you just searched out)

$sudo kill 290

9. Add the root permission for licd

$sudo lircd --permission 666

10. On your PC or laptop:

Open another terminal (T2). Download our configuration file from Github.

$git clone https://github.com/sunfounder/Sunfounder_IR_Media_Remote_Control_Lirc_config.git

PI7.png
Go to Sunfounder_IR_Media_Remote_Control_Lirc_config/:

$cd Sunfounder_IR_Media_Remote_Control_Lirc_config/

Copy the lircd.conf file to OSMC via the scp command (change the IP to your OSMC's)

$scp ./lircd.conf osmc@192.168.0.112:/home/osmc/

PI8.png
In terminal T1:
Copy lircd.conf to /etc/lirc/:

$cd ~
$sudo cp lircd.conf /etc/lirc/

11. Run the licd sever

$sudo /run/lirc/lircd-lirc0.sh

Since we've set "PREV" as the previous song, "NEXT" as the next song, "PLAY/PAUSE" as to play/pause, "+" as volume up, "-" as volume down, "EQ" as mute, "2" as up, "8" as down, "4" as left, "6" as right, "5" as OK, "7" as back. Finally it is all done! Now you can try pressing the buttons on your remote control!

Resource

lircd.confZIP.jpg