Difference between revisions of "I²C LCD1602"

From Wiki
Jump to: navigation, search
(Resources)
(Experimental Procedures)
Line 96: Line 96:
 
[[File:I2c_lcd102_1.png|800px|center]]
 
[[File:I2c_lcd102_1.png|800px|center]]
  
[http://www.sunfounder.com/wiki/index.php/File:PCF8574T_datasheet.pdf PCF8574T_datasheet][[File:PDF.jpg]]<br>
 
[http://www.sunfounder.com/learn/sensor-kit-v2-0-for-raspberry-pi-b-plus/lesson-30-i2c-lcd1602-sensor-kit-v2-0-for-b-plus.html Test_Experiment_for_Raspberry_Pi][[File:LINK.jpg]]<br>
 
[http://www.sunfounder.com/wiki/index.php?title=File:LiquidCrystal_I2C.zip LiquidCrystal_I2C library][[File:ZIP.jpg]]
 
 
=='''Note'''==
 
=='''Note'''==
 
If everything is correct,But the display just shows 16 black rectangles on Line 1.it may be the address of i2c is not 0x27,therfore you need to run the following code to read the address,then modify the 0x27 to which you read.
 
If everything is correct,But the display just shows 16 black rectangles on Line 1.it may be the address of i2c is not 0x27,therfore you need to run the following code to read the address,then modify the 0x27 to which you read.

Revision as of 04:02, 4 June 2016

Introduction

As we all know, though LCD and some other displays greatly enrich the man-machine interaction, they share a common weakness. When they are connected to a controller, multiple IOs will be occupied of the controller which has no so many outer ports. Also it restricts other functions of the controller. Therefore, LCD1602 with an I2C bus is developed to solve the problem.
I2C bus is a type of serial bus invented by PHLIPS. It is a high performance serial bus which has bus ruling and high or low speed device synchronization function required by multiple host system. I2C bus has only two bidirectional signal lines, Serial Data Line (SDA) and Serial Clock Line (SCL). The blue potentiometer on the I2C LCD1602 is used to adjust backlight to make it easier to display on the I2C LCD1602.
Back.png

Components

- 1 *SunFounder Uno board
- 1 * I2C LCD1602 module
- 1 * USB cable
- Several jump wires

Experimental Principle

In this experiment, we will let I2C LCD1602 display “SUNFOUNDER" and “hello, world" by programming.
I²C (Inter-Integrated Circuit), pronounced I-squared-C, is a multi-master, multi-slave, single-ended, serial computer bus invented by Philips Semiconductor (now NXP Semiconductors). It is typically used for attaching lower-speed peripheral ICs to processors and microcontrollers. Alternatively I²C is spelled I2C (pronounced I-two-C) or IIC (pronounced I-I-C).
I²C uses only two bidirectional open-drain lines, Serial Data Line (SDA) and Serial Clock Line (SCL), pulled up with resistors. Typical voltages used are +5 V or +3.3 V although systems I²C (Inter-Integrated Circuit), pronounced I-squared-C, is a multi-master, multi-slave, single-ended, serial computer bus invented by Philips Semiconductor (now NXP Semiconductors). It is typically used for attaching lower-speed peripheral ICs to processors and microcontrollers. Alternatively I²C is spelled I2C (pronounced I-two-C) or IIC (pronounced I-I-C).
I²C uses only two bidirectional open-drain lines, Serial Data Line (SDA) and Serial Clock Line (SCL), pulled up with resistors. Typical voltages used are +5 V or +3.3 V although systems with other voltages are permitted.
For more information about I2C operation principle, please visit I²C.

Experimental Procedures

Step 1: Connect the circuit
See the following table for connection between the I2C LCD1602 and the SunFounder Uno board:

I2C LCD1602 SunFounder Uno board
GND GND
VCC 5V
SDA A4
SCL A5
Experiment.png

Note: The wiring of I2C LCD1602 is the same through the following lessons.

Step 2: Program

/********************************
 * name:I2C LCD1602
 * function:You should now see your I2C LCD1602 display the flowing characters: "SunFounder" and "hello, world".
 ********************************/
//Email:support@sunfounder.com
//Website:www.sunfounder.com

/********************************/
// include the library code
#include <Wire.h> 
#include <LiquidCrystal_I2C.h>
/**********************************************************/
char array1[]=" SunFounder               ";  //the string to print on the LCD
char array2[]="hello, world!             ";  //the string to print on the LCD
int tim = 500;  //the value of delay time
// initialize the library with the numbers of the interface pins
LiquidCrystal_I2C lcd(0x27,16,2);  // set the LCD address to 0x27 for a 16 chars and 2 line display
/*********************************************************/
void setup()
{
  lcd.init();  //initialize the lcd
  lcd.backlight();  //open the backlight 
}
/*********************************************************/
void loop() 
{
  lcd.setCursor(15,0);  // set the cursor to column 15, line 0
  for (int positionCounter1 = 0; positionCounter1 < 26; positionCounter1++)
  {
    lcd.scrollDisplayLeft();  //Scrolls the contents of the display one space to the left.
    lcd.print(array1[positionCounter1]);  // Print a message to the LCD.
    delay(tim);  //wait for 250 microseconds
  }
  lcd.clear();  //Clears the LCD screen and positions the cursor in the upper-left corner.
  lcd.setCursor(15,1);  // set the cursor to column 15, line 1
  for (int positionCounter = 0; positionCounter < 26; positionCounter++)
  {
    lcd.scrollDisplayLeft();  //Scrolls the contents of the display one space to the left.
    lcd.print(array2[positionCounter]);  // Print a message to the LCD.
    delay(tim);  //wait for 250 microseconds
  }
  lcd.clear();  //Clears the LCD screen and positions the cursor in the upper-left corner.
}
/************************************************************/

Step 3: Compile the code
Before compiling the code, you need to add the LiquidCrystal_I2C file to the libraries of Arduino. If you don't know the libraries path, you can open Arduino IDE ,click File ->Preferences, as shown in the follwing diagram. Then add LiquidCrystal_I2C to the folder Libraries under the path

I2c lcd1602 2.png

Step 4: Upload the sketch to the SunFounder Uno board You should now see your I2C LCD1602 display the flowing characters "SunFounder" and "hello, world".

I2c lcd102 1.png

Note

If everything is correct,But the display just shows 16 black rectangles on Line 1.it may be the address of i2c is not 0x27,therfore you need to run the following code to read the address,then modify the 0x27 to which you read.

LiquidCrystal_I2C lcd(0x27,16,2);
/*****************************************************
 * name:I2C_Address
 * function:read the address of the I2C lcd1602
 * Connection:
 * I2C                 UNO 
 * GND                 GND
 * VCC                  5V
 * SDA                  A4(pin20 in mega2560)
 * SCL                  A5(pin21 in mega2560)
 ********************************************************/

#include <Wire.h>

void setup()
{
  Wire.begin();
  Serial.begin(9600);
  Serial.println("\nI2C Scanner");
}
void loop()
{
  byte error, address;
  int nDevices;
  Serial.println("Scanning...");
  nDevices = 0;
  for(address = 1; address < 127; address++ )
  {
    // The i2c_scanner uses the return value of
    // the Write.endTransmisstion to see if
    // a device did acknowledge to the address.
    Wire.beginTransmission(address);
    error = Wire.endTransmission();
    if (error == 0)
    {
      Serial.print("I2C device found at address 0x");
      if (address<16)
        Serial.print("0");
      Serial.print(address,HEX);
      Serial.println(" !");
      nDevices++;
    }
    else if (error==4)
    {
      Serial.print("Unknow error at address 0x");
      if (address<16)
        Serial.print("0");
      Serial.println(address,HEX);
    }
  }
  if (nDevices == 0)
    Serial.println("No I2C devices found\n");
  else
    Serial.println("done\n");
  delay(5000); // wait 5 seconds for next scan
}

Resources

PCF8574T_datasheetPDF.jpg
Test_Experiment_for_Raspberry_PiLINK.jpg
LiquidCrystal_I2C libraryZIP.jpg