GYML8511 UV Sensor

From Wiki
Revision as of 02:56, 13 November 2019 by Root (Talk | contribs) (Experimental Procedures for Arduino)

(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Jump to: navigation, search

Description

GYML8511 1.png GYML8511 2.png
The ML8511 is an UV sensor, which is suitable for acquiring UV intensity indoors or outdoors. The sensor IC applies SOI-CMOS technology so it is widely used in digital circuits and analogy circuits. According to the principle that photocurrent can be converted into voltage, the sensor can detect the UV intensity so it is a good choice for using in an external circuit. ML8511 can output analogy voltage that is proportional to UV intensity. Applications
Smart phone, Watch, Weather station, Bicycle navigation, Accessary, Gaming.

Features

  • Photodiode sensitive to UV-A and UV-B
  • Embedded operational amplifier
  • Analog voltage output
  • Low supply current (300A typ.) and low standby current (0.1A typ.)
  • Small and thin surface mount package (4.0mm x 3.7mm x 0.73mm, 12-pin ceramic QFN)

Introduction of Pins

Introduction of Pins
VIN Input terminal of the voltage before getting regulated
3V3 The anode of the power supply 3v3
GND The cathode of the power supply
OUT Output (Low in power down or standby mode)
EN Active high enable pin. (High: Active mode, Low: Standby mode)

Principle

GYML8511 3.png
GYML8511 4.png
GYML8511 5.png
TIMING CHART
Supply voltage and EN signal state should take one of the following procedures:

  1. EN should be HIGH or LOW at the same time when VDD is applied.
  2. EN should be HIGH or LOW while VDD is applied.

Output should be read after output voltage level becomes stable. Maximum time is required until stable output voltage reaches 1 millisecond after EN goes HIGH.
GYML8511 6.png

Experimental Procedures for Arduino

Step 1: Connect the circuit: 


GYML8511 7.png


//Hardware pin definitions
int UVOUT = A0; //Output from the sensor
int REF_3V3 = A1; //3.3V power on the Arduino board

void setup()
{
  Serial.begin(9600);

  pinMode(UVOUT, INPUT);
  pinMode(REF_3V3, INPUT);

  Serial.println("MP8511 example");
}

void loop()
{
  int uvLevel = averageAnalogRead(UVOUT);
  int refLevel = averageAnalogRead(REF_3V3);
  
  //Use the 3.3V power pin as a reference to get a very accurate output value from sensor
  float outputVoltage = 3.3 / refLevel * uvLevel;
  
  float uvIntensity = mapfloat(outputVoltage, 0.99, 2.9, 0.0, 15.0);

  Serial.print("MP8511 output: ");
  Serial.print(uvLevel);

  Serial.print(" MP8511 voltage: ");
  Serial.print(outputVoltage);

  Serial.print(" UV Intensity (mW/cm^2): ");
  Serial.print(uvIntensity);  
  
  Serial.println();
  
  delay(100);
}

//Takes an average of readings on a given pin
//Returns the average
int averageAnalogRead(int pinToRead)
{
  byte numberOfReadings = 8;
  unsigned int runningValue = 0; 

  for(int x = 0 ; x < numberOfReadings ; x++)
    runningValue += analogRead(pinToRead);
  runningValue /= numberOfReadings;

  return(runningValue);  
}

//The Arduino Map function but for floats
//From: http://forum.arduino.cc/index.php?topic=3922.0
float mapfloat(float x, float in_min, float in_max, float out_min, float out_max)
{
  return (x - in_min) * (out_max - out_min) / (in_max - in_min) + out_min;
}