Digital Accelerometer ADXL345 Module

From Wiki
Jump to: navigation, search

Introduction

Adxl345.png
The ADXL345 is a small, thin, low power, 3-axis accelerometer with high resolution (13-bit) measurement at up to ±16 g. Digital output data is formatted as 16-bit two’s complement and is accessible through either an SPI (3- or 4-wire) or I2C digital interface.
The ADXL345 is well suited to measure the static acceleration of gravity in tilt-sensing applications, as well as dynamic acceleration resulting from motion or shock. Its high resolution (4 mg/LSB) enables the inclination change measurement by less than 1.0°. And the excellent sensitivity (3.9mg/LSB @2g) provides a high-precision output of up to ±16g.
In this experiment, I2C digital interface is used.
See the following figure for the schematic diagram. There is a 3.3v voltage regulator chip in the circuit, so you can power the module with 5V or 3.3V.
ADXL345 works like this:
Zuobiao2.png
When you place the module face up, Z_OUT is at the maximum which is +1g; face down, Z_OUT is at the minimum. No matter of face, as long as it's placed on a level surface, X_OUT increases along the Ax axis direction, so does Y_OUT along the Ay axis. See the picture below. Thus, when you rotate the module, you can see the changes of X_OUT, Y_OUT, and Z_OUT. Zuobiao.png
</P>

Features

Ultra low power: 25 to 130 µA at VS = 2.5 V (typ)
Power consumption scales automatically with bandwidth
User selectable fixed 10-bit resolution or 4mg/LSB scale
factor in all g-ranges, up to 13-bit resolution at ±16 g
32 level output data FIFO minimizes host processor load
Built in motion detection functions
• Tap/Double Tap detection
• Activity/Inactivity monitoring
• Free-Fall detection
Supply and I/O voltage range: 1.8 V to 3.6 V
SPI (3 and 4 wire) and I2C digital interfaces
Flexible interrupt modes – Any interrupt mappable to either
interrupt pin
Measurement ranges selectable via serial command
Bandwidth selectable via serial command
Wide temperature range (-40 to +85°C)
10,000 g shock survival
Pb free/RoHS compliant
Small and thin: 3 × 5 × 1 mm LGA package</p>

Schematic

ADXL345 ad.png

Test

To use the ADXL345 with Arduino, you can take the following steps.

Step1:Connecting circuit It can share the I2C bus with other I2C devices as long as each device has a unique address. Only 4 connections are required for I2C communication.

ADXL345 ------- Arduino Uno/Mega2560
GND --------- GND
3.3V ------- 3.3V
SCL ------- A5 Uno/pin21 Mega2560
SDA ------- A4 Uno/pin20 Mega2560

ADXL345 bb.png
Step2: Upload the code

#include <Wire.h>  
#define Register_ID 0
#define Register_2D 0x2D
#define Register_X0 0x32
#define Register_X1 0x33
#define Register_Y0 0x34
#define Register_Y1 0x35
#define Register_Z0 0x36
#define Register_Z1 0x37
int ADXAddress = 0x53;  //I2C address
int reading = 0;
int val = 0;
int X0,X1,X_out;
int Y0,Y1,Y_out;
int Z1,Z0,Z_out;
double Xg,Yg,Zg;

void setup()
{
  Serial.begin(9600);
  delay(100);
  Wire.begin(); 
  delay(100);
  Wire.beginTransmission(ADXAddress);
  Wire.write(Register_2D);
  Wire.write(8);
  Wire.endTransmission();
  Serial.println("Accelerometer Test ");
} 
void loop()
{
  Wire.beginTransmission(ADXAddress);
  Wire.write(Register_X0);
  Wire.write(Register_X1);
  Wire.endTransmission();
  Wire.requestFrom(ADXAddress,2);
  if(Wire.available()<=2);
  {
    X0 = Wire.read();
    X1 = Wire.read();
    X1 = X1<<8;
    X_out = X0+X1;
  } 
  Wire.beginTransmission(ADXAddress);
  Wire.write(Register_Y0);
  Wire.write(Register_Y1);
  Wire.endTransmission();
  Wire.requestFrom(ADXAddress,2);
  if(Wire.available()<=2);
  {
    Y0 = Wire.read();
    Y1 = Wire.read();
    Y1 = Y1<<8;
    Y_out = Y0+Y1;
  } 
  Wire.beginTransmission(ADXAddress);
  Wire.write(Register_Z0);
  Wire.write(Register_Z1);
  Wire.endTransmission();
  Wire.requestFrom(ADXAddress,2);
  if(Wire.available()<=2);
  {
    Z0 = Wire.read();
    Z1 = Wire.read();
    Z1 = Z1<<8;
    Z_out = Z0+Z1;
  } 
  Xg = X_out/256.00;
  Yg = Y_out/256.00;
  Zg = Z_out/256.00;
  Serial.print("X=");
  Serial.print(Xg);
  Serial.print("\tY=");
  Serial.print(Yg);
  Serial.print("\tZ=");
  Serial.println(Zg);
  delay(300);  
}

Step3: Select correct Board and Port

Step4: Upload the sketch to the SunFounder Uno board

   After uploading, open Serial Monitor, where you can see the data detected. When the acceleration of the module changes, the figure will change accordingly on the window.

Adxl xinaxiang.jpg

Resource

ADXL345datasheetPDF.jpg
Test Experiment for Raspberry PiLINK.jpg