APM Current Sensor Power Module

From Wiki
Jump to: navigation, search

Introduction

Power module.jpg
This device is a DC-DC power supply module designed for the APM 2.0/2.5/2.5.2/2.6/2.8 and Pixhawk. It supports both voltage and current sensing and connects to the PM connector of APM or Pixhawk via a 6-pin cable, which is easy to use and provides stable and reliable supply. At most it supports an input of 28V and output of 5.3V, and a maximum 3A current. With stability and reliability, this module is the best choice for your flight control!
Note: The power module supplies only for devices including the flight control, receiver, GPS, data transmitter, OSD, air speedometer, etc. DO NOT supply servos by the module; otherwise the flight control or other devices may not work normally due to the large current consumed by some servos. Therefore, if the aircraft needs to carry servos, please supply them separately by BEC or built-in BEC of ESC.

Specifications

Input Voltage: Max 28V (2-6S Lithium battery)
Output Voltage: 5.3V
Max Output Current: 3A
Max Output Current: 90A
Voltage and current match with 5V ADC

Functions

T Plug

The battery connects to the Power Module’s male connector
Fdsgd.png
And the module's female connector plugs into your ESC or Power Distribution Board.
DFEFEWFE.jpg

6-Pin Port

The 6-pin port is to supply the Pixhawk/APM flight control and the 6-pin cable is provided.
Fhdsh.jpg
Pixhawk Power Port APM2.x Power Port

APM 2.x Power Module Notes:
Fsafsd.jpg
1. Please remember to remove the APM’s JP1 jumper when using the Power Module; in that case, only the APM board and the receiver get energy from the module’s on-board regulator instead of the ESCs.
1) After the jumper is removed, the APM’s servo output rail can be used to distribute power from the ESCs' BEC or separate UBEC to any servos or external devices.
2) If servos are used, plug an ESC BEC or separate UBEC power wire and ground wire into two of the power and ground pins on the APM’s servo output rail so servos can share a common power and ground bus.
2. You can leave the jumper as it is if you're using ESCs without BECs, or if the power wires of all the ESC BECs are cut and no servos need power from the servo out rail.
3. Also you can power each servo separately from each individual ESC-BEC.
1) Just run the power and ground from each ESC-BEC independently and directly to each servo (quite convenient for multicopters).

Power Switch

With the power switch on the module, when no power is needed, you can pull it OFF, so the battery will not supply devices and you don't need to remove it.
Power switch123.png

Configuration in Mission Planner

Step 1: Connect the flight controller into the computer
1. Check the voltage of your li-Po battery with a hand-held volt meter or a power analyzer
2. Connect your APM/PX4 to your computer and plug in the battery
MG 821534.jpg
Step 2: Open the Mission Planner, choose correct COM port,click CONNECT.
Portt.png

Step 3: click to INITIAL SETUP -> Optional Hardware -> Battery Monitor, enter the properties your module can measure, the type of module, the type of flight controller, and the battery capacity:
• Monitor: Voltage and Current or Battery Volts
• Sensor: Other
• APM Ver: Flight controller (e.g. Pixhawk )
• Battery Capacity: Battery capacity in mAh
Battteryyy.png
Step 2: Calibration
The bottom section of the Battery Monitor screen allows you to calibrate the voltage/current measurement in order to verify that the measured voltage of the battery is correct.
If you find the voltage is not correct (i.e. if off from the hand-held volt meter’s reading by more than perhaps 0.2V) you can correct the APM/PX4’s reading by doing the following:
1. On Mission Planner‘s INITIAL SETUP | Optional Hardware | Battery Monitor screen set the “Sensor” to “Other”.
2. Enter the voltage according to the hand-held volt meter in the “Measured Battery Voltage” field
3. Press the tab name or click out of the field and the “Voltage Divider (Calced)” value will update and the “Battery voltage (Calced)” should now equal the measured voltage

Using the power analyser you can also measure the current and compare to results displayed in the Mission Planner.
Note
Most current sensors are not very accurate at low currents (less than 3Amps). Typically you should perform current calibration at around 10A.
Enable Low Battery Alert You can set Mission Planner to alert you verbally when your battery is low (using a computerized voice).
Simply check the MP Alert on Low Battery checkbox and enter the warning you wish to hear, the voltage level and finally the percentage of remaining current.
Measured.png
Connecting power module to alternative pins
The power module is generally plugged into the default port on the flight controller (ie. Pixhawk). If you wish to change where the power module is plugged into the controller, the pins used can be modified using the BATT_VOLT_PIN and BATT_CURR_PIN parameters.
The list of available analog input pins that can be used are listed on the Hardware Options page for each board (Pixhawk, APM2).