Difference between revisions of "10.1 Inch Touch Screen for Raspberry Pi(NEW)"

From Wiki
Jump to: navigation, search
(Buttons)
(Buttons)
Line 39: Line 39:
 
On one side of the main board there are ports of HDMI input, 12V power input, and 5V/3A USB power output. <br><br>
 
On one side of the main board there are ports of HDMI input, 12V power input, and 5V/3A USB power output. <br><br>
 
[[File:10.1touch3.jpg]]<br><br>
 
[[File:10.1touch3.jpg]]<br><br>
 +
 +
== '''Burn the System to TF Card''' ==
 +
'''Note:'''<br><br>
 +
<ol>
 +
    <li>Do not install the Raspbian system by means of NOOBS, otherwise there appears touch failure.</li>
 +
    <li>On other displays, if you have installed the system on your Raspberry Pi by means of NOOBS, you can still use the 10.1-inch touch screen.</li>
 +
    <li>If you have already installed the system, you can directly skip this chapter. Turn to  next chapter to refer to Connect the Raspberry Pi and Screen, and you can get to use the 10.1-inch touch screen.</li>
 +
</lo>
 +
'''Step 1'''<br><br>
 +
Prepare the tool of image burning. Here we use the Etcher. You can download the software from the <br>
 +
link: https://www.balena.io/etcher/

Revision as of 08:09, 20 May 2020

Introduction

Resolution: 1280x800

Power: DC 12V/1.5A

Consumption: 4W

LCD Type: IPS

Capactive Touch

5-point Touch Screen

SunFounder 10.1 IPS monitor is a 5-point capacitive touch screen with a resolution of 1280x800, bringing you perfect visual experience. It works with various operating systems including Raspbian, Ubuntu, Ubuntu Mate, Windows, Android, and Chrome OS (you may need an USB extension cable).

10.1touch26.jpg


Hardware Description

LED Indicators

10.1touch1(1).jpg

There are 2 LED indicators on the main board of the screen to show different signals:

  • Power on the screen, after the green LED flashes one time, it lights on continuously; and the red LED lights on immediately.
  • If there's no HDMI signal, only the red LED will turn on.
  • If there's an HDMI signal, these two LEDs will turn on.
  • If you press the power button, the green LED will turn off and the red LED will keep turning on.
  • If you remove the power cord, both of the two LEDs will turn off.


Buttons

Buttons on the main board and their functions:

  • Power:Short press to switch ON/OFF(go into the sleep mode) the screen. Long press to power ON/OFF the device(Raspberry Pi).
  • B+:Increase screen brightness.
  • B-:Reduce screen brightness.
  • V+:Volume up.
  • V-:Volume down.

10.1touch2.jpg

On one side of the main board there are ports of HDMI input, 12V power input, and 5V/3A USB power output.

10.1touch3.jpg

Burn the System to TF Card

Note:

  1. Do not install the Raspbian system by means of NOOBS, otherwise there appears touch failure.
  2. On other displays, if you have installed the system on your Raspberry Pi by means of NOOBS, you can still use the 10.1-inch touch screen.
  3. If you have already installed the system, you can directly skip this chapter. Turn to next chapter to refer to Connect the Raspberry Pi and Screen, and you can get to use the 10.1-inch touch screen.
  4. </lo> Step 1

    Prepare the tool of image burning. Here we use the Etcher. You can download the software from the

    link: https://www.balena.io/etcher/