Difference between revisions of "10.1 Inch Touch Screen for Raspberry Pi"

From Wiki
Jump to: navigation, search
(3D-printed touch screen support)
(3D-printed touch screen support)
 
(3 intermediate revisions by the same user not shown)
Line 117: Line 117:
  
 
==3D-printed touch screen support==
 
==3D-printed touch screen support==
If you need to place the touch screen more conveniently, you can use a 3D printer to print a support. The relevant files required by the 3D printer are in the attachment. The 3D printing process is as follows
+
If you need to place the touch screen more conveniently, you can use a 3D printer to print a support. The relevant files required by the 3D printer are in the attachment [http://wiki.sunfounder.cc/index.php?title=File:Stand.zip stand.zip][[file:ZIP.jpg]]<br>.The 3D printing process is as follows
[http://wiki.sunfounder.cc/index.php?title=File:Stand.zip stand.zip][[file:ZIP.jpg]]<br>
+
 
 
1.Get ready for 3D printing
 
1.Get ready for 3D printing
 
   [[File:Touch1.JPG]]
 
   [[File:Touch1.JPG]]

Latest revision as of 10:05, 27 August 2018

Introduction

Touch Screen1.jpg
Italic text This SunFounder 10.1" IPS monitor is a 10-point capacitive touch screen with a resolution of 1280x800, bringing you perfect visual experience. It works with various operating systems including Raspbian, Ubuntu, Ubuntu Mate, Windows, Android, and Chrome OS(you may need an USB extension cable).

Features

Resolution: 1280x800
Size: 10.1"
LCD Type: IPS
Power: DC12V/2A
Consumption: 5W
Capacitive touch
10-point touch screen
Touch Screen2.jpg

Functions Description

Indication Lights

Touch Screen3.jpg

There are 2 LED indicators on the main board of the screen to show different signals:
Power on the screen and both the 2 LEDs will light up immediately.
If there's no HDMI signal, then only the green LED will be on.
If there's an HDMI signal, then only the red LED will be on.
Press and hold the switch to power off the display, and both LEDs will be off.
If you press the switch to sleep the device, the red LED will be on.

Buttons

Touch Screen4.jpg
Buttons on the main board and their functions:

a. Power
Press and hold to switch it off
Press to sleep/awake the device

b. Menu
To show menus
To confirm

c. V-
To go down on the Menu interface
Volume down on other interfaces

d. V+
To go up on the Menu interfacev Volume up on other interfaces

d. Exit
To exit

On one side of the main board there are ports for HDMI input, 12V/2A power input, and 5V/2.5A USB power output.
Touch Screen5.jpg
On the other side, you can see ports for 30-pin LVDS ribbon cable, 6-pin backlight control and 4-pin speaker.
Touch Screen6.jpg

Installation

The screen comes with seven 2.5*14.4 standoffs, two 2.5*22 ones, seven 2.5*6 ones, and some nuts for installing the Raspberry Pi to the screen. Take the following steps to complete the assembly.

Step 1. Fix the main board to the screen.

Place the main board onto the 4 2.5*6 copper standoffs pre-installed on the back case, with the buttons oriented to the case edge, and align the holes on the board and the standoffs.
Touch Screen7.png


Insert the 2.5*14.4 standoffs into the holes and tighten them.
Touch Screen8.jpg


Step 2. Fix the Raspberry Pi (or other boards) on the screen back case.

There are a vertical slot and a horizontal one on the back of the screen, so you can fix boards with different sizes by moving the nuts and 2.5*6 standoffs with the small wrench.
Touch Screen9.jpg
Touch Screen10.jpg


If you want to use a Raspberry Pi with the screen, then you don't need to adjust the standoffs since they are preset for it. Just place the board onto the case with holes on the RPi and the standoffs aligned, insert the 2.5*14.4 standoffs and fasten them.
Touch Screen11.jpg


Step 3. Insert the two 2.5*22 standoffs into the holes on the back to keep the screen balanced.

Touch Screen12.jpg


Step 4. Wiring.

1) Plug in the 6-pin backlight control cable into the LED BS port.
注释.jpg


2) Plug the 30-pin LVDS ribbon cable into the 30-pin headers (note that the red wires should be near the buttons side)
Touch Screen14.jpg
Touch Screen15.jpg


3) Connect the power port of the RPi to the USB port of the main board via a USB cable.
Touch Screen16.jpg


4) Connect the HDMI port of the RPi and the screen via an HDMI cable.
Touch Screen17.jpg


5) Connect the USB port of the RPi and the screen with a 4-pin USB cable.
Touch Screen18.jpg


6) Connect the power cable of the supply to power the main board of the screen.
Touch Screen19.jpg

Then power it on and the boot screen will appear.

Touch Screen20.jpg

Install the Virtual Keyboard

Open a terminal and run the command:

sudo apt-get install matchbox-keyboard

After the installation is done successfully, the keyboard will appear on the screen:
Touch Screen21.jpg

Using as Extension Screen for PC

Connect the computer and the main board via an HDMI cable, and the USB port of the PC and the screen with a 4-pin USB cable(you may need an USB extension cable for connection). Now you can use the screen as an extension one for your computer.
Touch Screen22.jpg

3D-printed touch screen support

If you need to place the touch screen more conveniently, you can use a 3D printer to print a support. The relevant files required by the 3D printer are in the attachment : stand.zipZIP.jpg
.The 3D printing process is as follows

1.Get ready for 3D printing

 Touch1.JPG

2.Install as shown

 Touch2 .JPG

3.Finish installation

 Touch3.JPG